СИСТЕМА ECD, Diagnostic DTC:P0500

DTC Code DTC Name
P0500 Vehicle Speed Sensor "A"

DESCRIPTION

The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A01IPQTE07
DTC No. DTC Detection Condition Trouble Area
P0500

Vehicle speed signal is not input to ECM regardless of whether vehicle is in motion

(2 trip detection logic)

  • Open or short in speedometer circuit

  • Speedometer assembly

  • ECM
Related Data List
DTC No. Data List
P0500 Vehicle Speed

WIRING DIAGRAM

A01IPBPE31

INSPECTION PROCEDURE

Note


  • When replacing the ECM, the ECM needs Registration and Initialization Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK OPERATION OF SPEEDOMETER


    1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

      Tech Tips

      The vehicle speed sensor is operating normally if the speedometer reading is normal.

      OK
      The vehicle speed sensor is operating normally.

    NG

    CHECK SPEEDOMETER CIRCUIT Click here

    OK

  2. READ VALUE USING GTS (VEHICLE SPEED)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

    5. Drive the vehicle.

    6. Read the value displayed on the GTS.

      OK
      Vehicle speeds displayed on GTS and speedometer display are equal.

    OK

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    NG

    CHECK HARNESS AND CONNECTOR (ECM OUTPUT VOLTAGE) Click here

  3. CHECK HARNESS AND CONNECTOR (ECM OUTPUT VOLTAGE)

    A01INS8E85
    Text in Illustration
    *a

    Front view of wire harness connector

    (to Combination Meter)

    1. Disconnect the combination meter connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H62-3 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V

    NG

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM) Click here

    OK

  4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

    A01IPYCE25
    Text in Illustration
    *a

    Component with harness connected

    (Combination Meter)

    1. Move the shift lever to neutral.

    2. Jack up the vehicle.

    3. Check the voltage between the terminal of the combination meter and the body ground while a wheel is turned slowly.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H62-3 (+S) - Body ground Ignition switch ON Voltage generated intermittently

      Tech Tips

      The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.

      Result
      Result Proceed to
      OK A
      NG B

    A

    REPLACE ECM Click here

    B

    REPLACE COMBINATION METER ASSEMBLY Click here

  5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)


    1. Disconnect the combination meter connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H62-3 (+S) - A76-51 (SPD) Always Below 1 Ω
      H62-3 (+S) or A76-51 (SPD) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  6. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. CHECK SPEEDOMETER CIRCUIT


    1. Check the speedometer circuit Click here.

      Tech Tips

      Inspect the brake actuator assembly and speed sensor.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. REPLACE COMBINATION METER ASSEMBLY


    1. Replace the combination meter Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  9. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END