СИСТЕМА ECD (для клапана регулирования всасывания), Diagnostic DTC:P2032, P2033

DTC Code DTC Name
P2032 Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2
P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2

DESCRIPTION

Refer to DTC P0545 Click here.

DTC No. DTC Detection Condition Trouble Area
P2032

Exhaust gas temperature sensor (for sensor 2) output voltage is 0.049 V or less for 0.6 seconds or more

(3 trip detection logic)

  • Open or short in exhaust gas temperature sensor (for sensor 2) circuit

  • Exhaust gas temperature sensor (for sensor 2)

  • ECM
DTC No. DTC Detection Condition Trouble Area
P2033

Exhaust gas temperature sensor (for sensor 2) output voltage is 4.99 V or more for 0.6 seconds or more

(3 trip detection logic)

  • Open or short in exhaust gas temperature sensor (for sensor 2) circuit

  • Exhaust gas temperature sensor (for sensor 2)

  • ECM
Related Data List
DTC No. Data List

P2032

P2033

 Exhaust Temperature B1S2

WIRING DIAGRAM

A01IP3KE88

INSPECTION PROCEDURE

Note

When replacing the ECM, the ECM needs Registration and Initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2)


    1. Using the GTS, check the value of Exhaust Temperature B1S2.


      1. Connect the GTS to the DLC3.

      2. Start the engine and warm it up.

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

      5. Read the value.

        Standard
        Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up).

    2. Inspect the exhaust gas temperature sensor (for sensor 2) Click here.


    NG

    REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2) - ECM)


    1. Disconnect the exhaust gas temperature sensor (for sensor 2) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C82-1 (THCO) - C112-109 (THCO) Always Below 1 Ω
      C82-2 (E2) - C112-110 (ETCO) Always Below 1 Ω
      C82-1 (THCO) or C112-109 (THCO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  4. REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2)


    1. Replace the exhaust gas temperature sensor (for sensor 2) Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END