HYBRID BATTERY SYSTEM, Diagnostic DTC:P0A85-123

DTC Code DTC Name
P0A85-123 Hybrid Battery Pack Cooling Fan 1 Control Circuit High

DESCRIPTION

Refer to the circuit description for DTC P0A84-123 Click here.

DTC No. INF Code DTC Detection Condition Trouble Area
PP0A85 123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target control speed range (1 trip detection)

  • Battery cooling blower assembly

  • Battery smart unit

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 Click here.

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work Click here.

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

  • When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK FOR DTCS (HV)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read output DTCs Click here.

      Result
      Result Proceed to
      P0AFC-123 is not output. A
      P0AFC-123 is also output. B

    5. Turn the power switch off.

    6. Disconnect the GTS from the DLC3.


    B

    GO TO DTC CHART (P0AFC-123) Click here

    A

  2. CHECK BATTERY SMART UNIT (FREQUENCY)


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

      Note


      • After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.

      • If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS Click here.

    6. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

      Note

      If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan.

    7. Enter the following menus: All Data / Cooling Fan Frequency 1.

    8. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    9. A0006SZE02
      Text in Illustration
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency 1) with the frequency value that was actually measured at the battery cooling blower assembly connector.

      Specified Condition
      Tester Connection Condition Specified Condition
      g1-2 (FP0) - g1-4 (GND0) Battery cooling blower assembly is operating Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10% or less.

      Note

      Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Tech Tips

      Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.

    10. Turn the power switch off.

    11. Disconnect the GTS from the DLC3.

    12. Disconnect the cable from the negative (-) auxiliary battery terminal.

    13. Install the luggage compartment front trim cover.


    OK

    REPLACE BATTERY COOLING BLOWER ASSEMBLY Click here

    NG

    REPLACE BATTERY SMART UNIT Click here