HYBRID BATTERY SYSTEM, Diagnostic DTC:P0A84-123

Info Added 2017-08-02

DTC Code DTC Name
P0A84-123 Hybrid Battery Pack Cooling Fan 1 Control Circuit Low

DESCRIPTION


DTC No. INF Code DTC Detection Condition Trouble Area
P0A84 123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target control speed range (1 trip detection)

  • Wire harness or connector

  • BATT FAN fuse

  • Battery cooling blower assembly

  • Battery smart unit

  • Power management control ECU

WIRING DIAGRAM

B001VJNE19

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work Click here.

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK FOR DTCS (HV)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read output DTCs Click here.

      Result
      Result Proceed to
      P0AFC-123 is not output. A
      P0AFC-123 is also output. B

    5. Turn the power switch off.

    6. Disconnect the GTS from the DLC3.


    B

    GO TO DTC CHART (P0AFC-123) Click here

    A

  2. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

      Note

      If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

    4. Select air volume mode 6 in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    5. Check that the fan operates and air is sucked into the inlet duct.

      Tech Tips

      The cooling fan may not stop even when turning the cooling fan off in the "Driving the Battery Cooling Fan" Active Test. This is due to HV system control and not a malfunction.

      OK
      The fan operates.

    6. Turn the power switch off.


    NG

    CHECK FUSE (BATT FAN) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Remove the rear side seat back assembly LH.

    4. Disconnect the g1 battery cooling blower assembly connector.

    5. Disconnect the P10 battery smart unit connector.

    6. B001VJSE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Smart Unit)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      g1-2 (FP0) - P10-5 (FP0) Power switch off Below 1 Ω
      g1-2 (FP0) or P10-5 (FP0) - Body ground Power switch off 10 kΩ or higher

    7. Connect the cable to the negative (-) auxiliary battery terminal.

    8. Turn the power switch on (IG).

    9. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      g1-2 (FP0) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

      Tech Tips

      As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

      Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) auxiliary battery terminal.

    12. Reconnect the P10 battery smart unit connector.

    13. Reconnect the g1 battery cooling blower assembly connector.

    14. Install the rear side seat back assembly LH.

    15. Install the luggage compartment front trim cover.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

    OK

  4. READ VALUE USING GTS (COOLING FAN FREQUENCY)


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

      Note


      • After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.

      • If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS Click here.

    6. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    7. Clear the DTCs and freeze frame data Click here.

    8. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

      Note

      If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan assembly (No. 0).

    9. Enter the following menus: All Data / Cooling Fan Frequency 1.

    10. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    11. B001VDRC03
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

      Standard
      Tester Connection Condition
      g1-2 (FP0) - g1-4 (GND0) Battery cooling blower is operating

      Note

      Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Tech Tips

      Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

      Result
      Result Proceed to
      The value in the Data List (Cooling Fan Frequency1) and the actual measured value at the battery cooling blower assembly connector are 0 Hz. A
      Other than above B

    12. Turn the power switch off.

    13. Disconnect the cable from the negative (-) auxiliary battery terminal.

    14. Install the luggage compartment front trim cover.


    B

    CHECK BATTERY SMART UNIT (FREQUENCY) Click here

    A

  5. CHECK BATTERY SMART UNIT


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Disconnect the g1 battery cooling blower assembly connector.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Turn the power switch on (IG).

      Note


      • After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

      • If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS Click here.

    6. B001VEJC24
      *a

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      g1-2 (FP0) - g1-4 (GND0) Power switch on (IG) 4.5 to 5.5 V

      Note

      Turning the power switch on (IG) with the battery cooling blower assembly connector and hybrid vehicle control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

    9. Reconnect the g1 battery cooling blower assembly connector.

    10. Install the luggage compartment front trim cover.


    OK

    REPLACE BATTERY COOLING BLOWER ASSEMBLY Click here

    NG

    REPLACE BATTERY SMART UNIT Click here

  6. CHECK BATTERY SMART UNIT (FREQUENCY)


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

      Note


      • After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.

      • If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS Click here.

    6. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

      Note

      If the Active Test cannot be performed, skip it and proceed to the next step to check Frequency. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

    7. Enter the following menus: All Data / Cooling Fan Frequency 1.

    8. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    9. A0006SZE03
      Text in Illustration
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

      Specified Condition
      Tester Connection Condition Specified Condition
      g1-2 (FP0) - g1-4 (GND0) Battery cooling blower is operating Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10 % or less.

      Note

      Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Tech Tips

      Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) auxiliary battery terminal.

    12. Install the luggage compartment front trim cover.


    OK

    REPLACE BATTERY COOLING BLOWER ASSEMBLY Click here

    NG

    REPLACE BATTERY SMART UNIT Click here

  7. CHECK FUSE (BATT FAN)


    1. Remove the BATT FAN fuse from the No. 2 engine room relay block.

    2. B001VCFE01
      Text in Illustration
      *1 No. 2 Engine Room Relay Block
      *2 BATT FAN Fuse

      Measure the resistance of the BATT FAN fuse.

      Standard Resistance
      Tester Connection Condition Specified Condition
      BATT FAN fuse Always Below 1 Ω

    3. Install the BATT FAN fuse to the No. 2 engine room relay block.


    NG

    CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY) Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (VOLTAGE)


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

      Note


      • After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

      • If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS Click here.

    6. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    7. Clear DTCs and freeze frame data Click here.

      Note

      When DTCs are cleared, freeze frame data and INF codes are also cleared.

    8. B001VGKC01
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      g1-1 (IG0) - g1-4 (GND0) Power switch on (IG) 11 to 14 V

      Note

      Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Tech Tips

      Measure the voltage on the wire side of the connector that is part of the battery cooling blower.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

    11. Install the luggage compartment front trim cover.


    NG

    CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND) Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Disconnect the g1 battery cooling blower assembly connector.

    4. Disconnect the A31 power management control ECU connector Click here.

    5. B001VGUE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      g1-3 (SI0) - A31-29 (SI0) Power switch off Below 1 Ω
      g1-3 (SI0) or A31-29 (SI0) - Body ground Power switch off 10 kΩ or higher

      Note

      When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

    6. Connect the cable to the negative (-) auxiliary battery terminal.

    7. Turn the power switch on (IG).

    8. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      g1-3 (SI0) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the battery cooling blower assembly connector and power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

    11. Reconnect the g1 battery cooling blower assembly connector.

    12. Install the luggage compartment front trim cover.

    13. Reconnect the A31 power management control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK POWER MANAGEMENT CONTROL ECU


    1. Remove the power management control ECU.

      Click here

    2. B001VDLC01
      *a

      Component without harness connected

      (Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Specified Condition
      A31-29 (SI0) - H1-5 (E01) 10 kΩ or higher

    3. Install the power management control ECU.


    NG

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    OK

  11. CHECK POWER MANAGEMENT CONTROL ECU (SI0 VOLTAGE)


    1. Turn the power switch on (IG).

    2. B001VE1C80
      *a

      Component with harness connected

      (Power Management Control ECU)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A31-29 (SI0) - H1-5 (E01) Power switch on (IG) 4.5 to 5.5 V

    3. Turn the power switch off.


    NG

    REPLACE BATTERY COOLING BLOWER ASSEMBLY Click here

    OK

  12. CHECK BATTERY COOLING BLOWER ASSEMBLY


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

      Note


      • After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

      • If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS Click here.

    6. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    7. Clear the DTCs and freeze frame data Click here.

    8. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

    9. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

      Note

      If the Active Test cannot be performed, skip it and proceed to the next step to check frequency. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan.

    10. B001VDRC04
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      Connect an oscilloscope to the g1 battery cooling blower assembly connector and check the waveform.

      Item Content
      Tester Connection g1-3 (SI0) - g1-4 (GND0)
      Equipment Setting 10 V/DIV.,1 ms/DIV.
      Condition Power switch on (IG) during Active Test

      Note

      Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Tech Tips


      • Perform this inspection with the battery cooling blower assembly connector connected.

      • The wave length will vary with the operating speed of the battery cooling blower assembly.

    11. Turn the power switch off.

    12. Disconnect the cable from the negative (-) auxiliary battery terminal.

    13. B001VC4C01
      *a Waveform 1

      Install the luggage compartment front trim cover.

      Result
      Result Proceed to
      Normal (The pulse output of waveform 1) A
      No pulse generation B

    A

    REPLACE BATTERY COOLING BLOWER ASSEMBLY Click here

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

  13. CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the luggage compartment front trim cover.

      Click here

    3. B001VDRC05
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly)
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      g1-4 (GND0) - Body ground Power switch off Below 1 Ω

    4. Install the luggage compartment front trim cover.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)


    1. Disconnect the H1 power management control ECU connector Click here.

    2. B001VI9E03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H1-5 (E01) - Body ground Power switch off Below 1 Ω

      Note

      When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

    3. Reconnect the H1 power management control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)


    1. Disconnect the H2 power management control ECU connector Click here.

    2. B001VEBE03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-5 (E02) - Body ground Power switch off Below 1 Ω

      Note

      When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

    3. Reconnect the H2 power management control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)


    1. Remove the IGCT relay.

    2. Remove the luggage compartment front trim cover Click here.

    3. Disconnect the g1 battery cooling blower assembly connector.

    4. B001VCSE03
      Text in Illustration
      *1 No. 2 Engine Room Relay Block
      *2 IGCT Relay
      *a

      Front view of wire harness connector

      (to Battery Cooling Blower Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5 (IGCT relay block) - g1-1 (IG0) Power switch off Below 1 Ω

    5. Install the IGCT relay.

    6. Reconnect the g1 battery cooling blower assembly connector.

    7. Install the luggage compartment front trim cover.


    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  17. CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)


    1. Remove the BATT FAN fuse.

    2. Remove the luggage compartment front trim cover Click here.

    3. Disconnect the g1 battery cooling blower assembly connector.

    4. B001VJVE03
      Text in Illustration
      *1 No. 2 Engine Room Relay Block
      *2 BATT FAN fuse
      *a

      Front view of wire harness connector

      (to Battery Cooling Blower Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      g1-1 (IG0) - Terminals except 2 (BATT FAN fuse block) and body ground Power switch off 10 kΩ or higher

    5. Install the BATT FAN fuse.

    6. Reconnect the g1 battery cooling blower assembly connector.

    7. Install the luggage compartment front trim cover.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  18. CHECK BATTERY COOLING BLOWER ASSEMBLY


    1. Remove the luggage compartment front trim cover Click here.

    2. Disconnect the g1 battery cooling blower assembly connector.

    3. B001VDME03
      Text in Illustration
      *a

      Component without harness connected

      (Battery Cooling Blower Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      g1-1 (IG0) - g1-4 (GND0) and body ground Power switch off 10 kΩ or higher

    4. Reconnect the g1 battery cooling blower assembly connector.

    5. Install the luggage compartment front trim cover.


    OK

    REPLACE FUSE (BATT FAN)

    NG

    REPLACE BATTERY COOLING BLOWER ASSEMBLY Click here

  19. REPAIR OR REPLACE HARNESS OR CONNECTOR


    NEXT

    REPLACE FUSE (BATT FAN)

  20. REPLACE BATTERY COOLING BLOWER ASSEMBLY

    Click here


    NEXT

    REPLACE FUSE (BATT FAN)