HYBRID CONTROL SYSTEM, Diagnostic DTC:P0A09-591

Info Added 2017-08-02

DTC Code DTC Name
P0A09-591 DC / DC Converter Status Circuit Low Input

DESCRIPTION

The DC/DC converter controls output voltage (12 V) based on duty ratio signals sent from the power management control ECU.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A09 591 DC/DC converter voltage switching (VLO) signal circuit malfunction (Open or short to GND)

  • Wire harness or connector

  • Inverter with converter assembly

  • Power management control ECU

WIRING DIAGRAM

A00076SE01
*1 Inverter with Converter Assembly
*2 Power Management Control ECU

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work Click here.

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    1. A0005OEE01
      Text in Illustration
      *A for LHD
      *B for RHD

      Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors Click here.

      OK
      The connectors are connected securely and there are no contact pressure problems.

    NG

    CONNECT SECURELY

    OK

  2. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Check the connector connections and contact pressure of the low voltage connectors of the inverter with converter assembly Click here.

      Note

      Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

      A00046KE03
      OK
      The connectors are connected securely and there are no contact pressure problems.

      Tech Tips

      When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.


    NG

    CONNECT SECURELY

    OK

  3. CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)


    1. Connect an oscilloscope between the power management control ECU terminals specified in the table below.

    2. Turn the power switch on (IG).

    3. A00090GE02
      Text in Illustration
      *a

      Component with harness connected

      (Power Management Control ECU)

      Measure the waveform.

      Item Content
      Terminal A31-11 (VLO) - H1-6 (E1)
      Equipment Setting 5 V/DIV., 50 ms/DIV.
      Condition Power switch on (IG)
      OK
      The waveform appears as shown in the illustration.

      Tech Tips


      • Perform this inspection with the power management control ECU connector connected.

    4. Turn the power switch off.


    NG

    CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF VLO INSIDE POWER MANAGEMENT CONTROL ECU) Click here

    OK

  4. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Clear the DTCs and freeze frame data.

    5. Turn the power switch off.


    NEXT

  5. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (READY).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.

      Result
      Result Proceed to
      P0A09-591 is not output. A
      P0A09-591 is output again. B

    5. Turn the power switch off.


    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

  6. CHECK FOR INTERMITTENT PROBLEMS

    Click here


    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

  7. CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF VLO INSIDE POWER MANAGEMENT CONTROL ECU)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Disconnect the A13 inverter with converter assembly connector.

    3. A00041XE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Inverter with Converter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-6 (VLO) - Body ground Power switch off 370 to 430 kΩ

    4. Reconnect the A13 inverter with converter assembly connector.


    OK

    REPLACE INVERTER WITH CONVERTER ASSEMBLY Click here

    NG

  8. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Disconnect the A13 inverter with converter assembly connector.

    3. Disconnect the A31 power management control ECU connector.

    4. A0009J6E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Inverter with Converter Assembly)
      *b

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-6 (VLO) - A31-11 (VLO) Power switch off Below 1 Ω
      A13-6 (VLO) or A31-11 (VLO) - Body ground and other terminals Power switch off 10 kΩ or higher

    5. Reconnect the A13 inverter with converter assembly connector.

    6. Reconnect the A31 power management control ECU connector.


    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR