Click here

HYBRID CONTROL SYSTEM, Diagnostic DTC:P3108-536

Click here
Click here
DTC Code DTC Name
P3108-536 Lost Communication with A/C System Control Module
Click here

DESCRIPTION

The power management control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.

DTC No. INF Code DTC Detection Condition Trouble Area
P3108 536 A/C inverter malfunction

  • Wire harness or connector

  • Compressor with motor assembly

  • Power management control ECU
Table 1. *a Compressor with Motor Assembly *b Power Management Control ECU
Click here

WIRING DIAGRAM

Click here

PROCEDURE


  1. Click here

    CHECK DTC OUTPUT (AIR CONDITIONER)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.

    4. Check if DTCs related to the air conditioning system (A/C) are output.

      Result
      Result Proceed to
      DTCs related to A/C are not output. A
      DTCs related to A/C are output. B

    5. Turn the power switch off.


  2. Click here

    CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    1. A0009DG

      Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

      OK
      The connectors are connected securely and there are no contact pressure problems.

  3. Click here

    CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)


    1. A0007Y3E03

      Check the connection of connector D60 of the compressor with motor assembly.

      OK
      The connector is connected securely and there are no contact problems.

  4. Click here

    CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)


    1. Disconnect the D60 compressor with motor assembly connector.

    2. A0004IPE03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D60-5 (GND) - Body ground Power switch off Below 1 Ω
      Table 2. Text in Illustration
      *a

      Front view of wire harness connector

      (to Compressor with Motor Assembly)

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D60-6 (IG1) - D60-5 (GND) Power switch on (IG) 11 to 14 V
      Note:

      Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Reconnect the D60 compressor with motor assembly connector.


    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. Click here

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)


    1. Disconnect the A31 power management control ECU connector.

    2. Disconnect the D60 compressor with motor assembly connector.

    3. Turn the power switch on (IG).

    4. A000944E03

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A31-19 (CLK) - Body ground Power switch on (IG) Below 1 V
      A31-20 (STB) - Body ground Power switch on (IG) Below 1 V
      A31-30 (ETI) - Body ground Power switch on (IG) Below 1 V
      A31-31 (ITE) - Body ground Power switch on (IG) Below 1 V
      Table 3. Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)
      *b

      Front view of wire harness connector

      (to Compressor with Motor Assembly)
      Note:

      Turning the power switch on (IG) with the power management control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A31-19 (CLK) - D60-1 (CLK) Power switch off Below 1 Ω
      A31-20 (STB) - D60-4 (STBI) Power switch off Below 1 Ω
      A31-30 (ETI) - D60-3 (DOUT) Power switch off Below 1 Ω
      A31-31 (ITE) - D60-2 (DIN) Power switch off Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A31-19 (CLK) or D60-1 (CLK) - Body ground and other terminals Power switch off 10 kΩ or higher
      A31-20 (STB) or D60-4 (STBI) - Body ground and other terminals Power switch off 10 kΩ or higher
      A31-30 (ETI) or D60-3 (DOUT) - Body ground and other terminals Power switch off 10 kΩ or higher
      A31-31 (ITE) or D60-2 (DIN) - Body ground and other terminals Power switch off 10 kΩ or higher

    7. Reconnect the D60 compressor with motor assembly connector.

    8. Reconnect the A31 power management control ECU connector.


    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    CHECK POWER MANAGEMENT CONTROL ECU


    1. Disconnect the D60 compressor with motor assembly connector.

    2. A0006IXE01

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D60-3 (DOUT) - Body ground Power switch off 10 kΩ or higher
      D60-4 (STBI) - Body ground Power switch off 10 kΩ or higher
      Table 4. Text in Illustration
      *a

      Front view of wire harness connector

      (to Compressor with Motor Assembly)

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D60-1 (CLK) - Body ground Power switch on (IG) 11 to 14 V
      D60-2 (DIN) - Body ground Power switch on (IG) 11 to 14 V
      D60-3 (DOUT) - Body ground Power switch on (IG) Below 1 V
      D60-4 (STBI) - Body ground Power switch on (IG) Below 1 V
      Note:

      Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Reconnect the D60 compressor with motor assembly connector.


  7. Click here

    CHECK COMPRESSOR WITH MOTOR ASSEMBLY


    1. Disconnect the A31 power management control ECU connector.

    2. A00053KE02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A31-19 (CLK) - Body ground Power switch off 10 kΩ or higher
      A31-31 (ITE) - Body ground Power switch off 10 kΩ or higher
      Table 5. Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A31-19 (CLK) - Body ground Power switch on (IG) Below 1 V
      A31-20 (STB) - Body ground Power switch on (IG) 11 to 14 V
      A31-30 (ETI) - Body ground Power switch on (IG) 11 to 14 V
      A31-31 (ITE) - Body ground Power switch on (IG) Below 1 V
      Note:

      Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Reconnect the A31 power management control ECU connector.


    • OK

      REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

    • NG

      REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)