HYBRID CONTROL SYSTEM, Diagnostic DTC:P3107-213

DESCRIPTION

The power management control ECU detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.

PROCEDURE

1. Click here

   CHECK DTC OUTPUT (SRS AIRBAG)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.

   4. Check for DTCs.

      Result
      Result Proceed to Airbag system DTCs are not output. A Airbag system DTCs are output. B

   5. Turn the power switch off.

   
   
   • AClick here
   • B

     GO TO DTC CHART (AIRBAG SYSTEM) (Click here)

2. Click here

   CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

   
   

   1. Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.

   2. Turn the power switch on (READY).

   3. 

      Measure the waveform.

      Item	Contents
      Terminal	H36-14 (GSW2) - H36-25 (E1)
      Equipment Setting	5V/DIV., 500ms/DIV.
      Condition	Power switch on (READY)

      Result
      Result Proceed to The waveform appears as shown in the illustration. A The waveform differs from the one shown in the illustration. B

      Table 2. Text in Illustration

      *a	Component with harness connected (Airbag Sensor Assembly)

   4. Turn the power switch off.

   
   
   • AClick here
   • BClick here
3. Click here

   CLEAR DTC

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

   4. Clear the DTCs and freeze frame data.

   5. Turn the power switch off.

   
   
   • NEXTClick here
4. Click here

   CHECK DTC OUTPUT (HYBRID CONTROL)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

   4. Check for DTCs.

      Result
      Result Proceed to P3107-213 is not output. A P3107-213 is output. B

   5. Turn the power switch off.

   
   
   • AClick here
   • B

     REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

5. Click here

   CHECK FOR INTERMITTENT PROBLEMS

   (Click here)

   
   
   • OK

     REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

   • NG

     REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6. Click here

   CHECK AIRBAG SENSOR ASSEMBLY

   
   

   1. Disconnect the H36 airbag sensor assembly connector.

   2. 

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H36-14 (GSW2) - H36-25 (E1) Power switch off 10 kΩ or higher

      Table 3. Text in Illustration

      *a	Component without harness connected (Airbag Sensor Assembly)

   3. Reconnect the H36 airbag sensor assembly connector.

   
   
   • OKClick here
   • NG

     REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

7. Click here

   CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

   
   

   1. Disconnect the H1 power management control ECU connector.

   2. Disconnect the H36 airbag sensor assembly connector.

   3. 

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H1-29 (ABFS) or H36-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher

      Table 4. Text in Illustration

      *a	Rear view of wire harness connector (to Power Management Control ECU)
      *b	Rear view of wire harness connector (to Airbag Sensor Assembly)

   4. Reconnect the H36 airbag sensor assembly connector.

   5. Reconnect the H1 power management control ECU connector.

   
   
   • OK

     REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

   • NG

     REPAIR OR REPLACE HARNESS OR CONNECTOR