REAR AXLE CARRIER INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

   
   

   1. Install the rear axle carrier sub-assembly to the rear shock absorber assembly with the 2 bolts and 2 nuts.

      290 N*m

      2957 kgf*cm

      214 ft.*lbf

      Note:

      While keeping the bolts from rotating, tighten the nuts.

      Tip:

      Insert the bolt from the rear of the vehicle.

2. Click here

   TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

   
   

   1. Connect the rear No. 1 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

      Note:

      When temporarily tightening the bolt, keep the nut from rotating.

      Tip:

      Insert the bolt from the front of the vehicle.

3. Click here

   TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

   
   

   1. Connect the rear No. 2 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

      Note:

      When temporarily tightening the bolt, keep the nut from rotating.

      Tip:

      Insert the bolt from the rear of the vehicle.

4. Click here

   TEMPORARILY TIGHTEN REAR STRUT ROD ASSEMBLY

   
   
   1. 

      Temporarily tighten the rear strut rod assembly (rear side) to the rear axle carrier sub-assembly with the bolt and nut.

      Note:

      Since a stopper nut is used, turn the bolt.

      Tip:

      Insert the bolt from the inside of the vehicle.

5. Click here

   INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

   Click here

6. Click here

   CONNECT SKID CONTROL SENSOR WIRE

   Click here

7. Click here

   INSTALL REAR DISC

   Click here

8. Click here

   INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

   Click here

9. Click here

   INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

   Click here

10. Click here

    STABILIZE SUSPENSION

    
    
    1. 

       Jack up the rear axle carrier sub-assembly, placing a wooden block under it to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm assembly (inner side) is horizontally aligned with the center of the rear axle hub.

       Table 1. Text in Illustration

       *1	Wooden Block

       CAUTION:

       Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

       Note:
       

       • When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.

       • Make sure to perform this operation with the vehicle kept as low as possible.

11. Click here

    FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

    
    
    1. 

       Fully tighten the bolt.

       100 N*m

       1020 kgf*cm

       74 ft.*lbf

       Note:

       Since a stopper nut is used, fully tighten the bolt.

12. Click here

    FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

    
    
    1. 

       Fully tighten the bolt.

       100 N*m

       1020 kgf*cm

       74 ft.*lbf

       Note:

       Since a stopper nut is used, fully tighten the bolt.

13. Click here

    FULLY TIGHTEN REAR STRUT ROD ASSEMBLY

    
    
    1. 

       Fully tighten the bolt.

       80 N*m

       816 kgf*cm

       59 ft.*lbf

       Note:

       Since a stopper nut is used, fully tighten the bolt.

14. Click here

    INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (for RH Side)

    (Click here)

15. Click here

    CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    
    

    1. Connect the cable to the negative (-) auxiliary battery terminal (Click here).

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs (Click here).

16. Click here

    INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

17. Click here

    INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

    Tip:

    Use the same procedure as for LHD (Click here).

18. Click here

    ADJUST PARKING BRAKE

    (Click here)

19. Click here

    INSTALL REAR WHEEL

    103 N*m

    1049 kgf*cm

    76 ft.*lbf

20. Click here

    INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    (Click here)

21. Click here

    CHECK FOR SPEED SENSOR SIGNAL

    (Click here)