REAR SHOCK ABSORBER REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

    Click here

  2. REMOVE REAR WHEEL

  3. SEPARATE REAR STABILIZER LINK ASSEMBLY


    1. A0008K7

      Remove the nut and separate the rear stabilizer link assembly from the rear shock absorber with coil spring.

      If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.

  4. SEPARATE REAR FLEXIBLE HOSE


    1. A0008A7

      Remove the bolt and separate the rear flexible hose from the rear shock absorber with coil spring.

  5. SEPARATE SKID CONTROL SENSOR WIRE


    1. A0006AX

      Remove the bolt and separate the skid control sensor wire from the rear shock absorber with coil spring.

  6. REMOVE REAR NO. 1 SUSPENSION SUPPORT COVER


    1. A000530

      Using a screwdriver, disengage the 4 claws and remove the rear No. 1 suspension support cover.

  7. REMOVE REAR SHOCK ABSORBER WITH COIL SPRING


    1. A0009NRE07
      Text in Illustration
      *1 Jack
      *2 Wooden Block

      Support the rear axle carrier sub-assembly with a jack using a wooden block.

      Tech Tips

      Support the rear axle carrier sub-assembly until reinstallation of the rear shock absorber with coil spring is complete.

    2. A0005ZH

      Loosen the rear support to rear shock absorber nut of the rear shock absorber assembly.

      Note


      • Do not remove the rear support to rear shock absorber nut.

      • Loosen the nut only when the rear shock absorber with coil spring needs to be disassembled.

    3. A0005WD

      Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring from the rear axle carrier sub-assembly.

      Note

      When removing the nuts, keep the bolts from rotating.

    4. A0006PC

      Remove the 3 nuts and rear shock absorber with coil spring.

      Note

      Make sure that the skid control sensor wire and rear flexible hose are disconnected from the rear shock absorber with coil spring.

  8. REMOVE REAR SUPPORT TO REAR SHOCK ABSORBER NUT


    1. A00050ME06

      Secure SST in a vise.

      SST
      09727-30021   ( 09727-00010, 09727-00021, 09727-00031 )
    2. A0007TA

      Attach the arm of SST to the diameter of the rear coil spring.

      CAUTION:


      • Make sure that the rear coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

      • Make sure that the claws of the hooks are securely attached.

    3. Using SST, compress the rear coil spring.

      CAUTION:


      • If the rear coil spring bends during the compression, immediately stop the compression and reinstall SST.

      • Do not compress the spring until the coil springs contact each other.

      • Do not use an impact wrench. It will damage SST.

    4. Confirm that the rear coil spring becomes free and remove the rear support to rear shock absorber nut.

      CAUTION:

      Do not remove the rear support to rear shock absorber nut when the rear coil spring is not free.

  9. REMOVE REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR

  10. REMOVE REAR SUSPENSION SUPPORT ASSEMBLY

  11. REMOVE REAR NO. 1 SPRING BUMPER

  12. REMOVE REAR COIL SPRING

  13. REMOVE REAR LOWER COIL SPRING INSULATOR

  14. REMOVE REAR SHOCK ABSORBER ASSEMBLY