LANE DEPARTURE ALERT SYSTEM(w/ Steering Control), Diagnostic DTC:C1AAD

DTC Code DTC Name
C1AAD Vehicle Information Initialization Incomplete

DESCRIPTION

When the forward recognition camera is replaced with a new one, it stores the vehicle information received from the hybrid vehicle control ECU assembly. If the forward recognition camera cannot store the vehicle information, DTC C1AAD is stored.

DTC No. DTC Detection Condition Trouble Area
C1AAD When the power switch is turned on (IG) and the system is activated, the vehicle information from the hybrid vehicle control ECU assembly cannot be confirmed.

  • CAN communication system

  • Forward recognition camera

  • Hybrid vehicle control ECU assembly

CAUTION / NOTICE / HINT

Note


  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

  • If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust Click here.

PROCEDURE


  1. CHECK DTC OUTPUT (CAN COMMUNICATION DTC OUTPUT)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC U0293 is not output A
      DTC U0293 is output B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / Front Recognition Camera / Data List.

    5. Read the Data List according to the display on the GTS.

      Chassis > Front Recognition Camera > Data List
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Information (2WD/4WD)

      Vehicle information/

      2WD, 4WD or Unknown

      2WD: for 2WD

      4WD: for AWD

      Unknown: Vehicle information not confirmed

      		 -
      Vehicle Information (Conv/HV)

      Vehicle information/

      Conv, HV or Unknown

      Conv: Conventional

      HV: Hybrid vehicle

      Unknown: Vehicle information not confirmed

      		 -

      Tech Tips


      • If "Unknown" is displayed, the hybrid vehicle control ECU assembly cannot send vehicle information or the forward recognition camera cannot store the vehicle information. Check for DTCs, replace the hybrid vehicle control ECU assembly and recheck for DTCs. If the DTC is output again, replace the forward recognition camera.

      • If "Unknown" is not displayed, the DTC is stored even though the vehicle information is stored in the forward recognition camera. Replace the forward recognition camera.

      Result
      Result Proceed to
      "Unknown" is displayed A
      "Unknown" is not displayed B

    B

    REPLACE FORWARD RECOGNITION CAMERA Click here

    A

  3. CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Wait for approximately 1 minute.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1AAD is output A
      DTC C1AAD is not output B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  4. REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY


    1. Replace the hybrid vehicle control ECU assembly Click here.


    NEXT

  5. CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Clear the DTCs Click here.

    6. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1AAD is output A
      DTC C1AAD is not output B

    A

    REPLACE FORWARD RECOGNITION CAMERA Click here

    B

    END (HYBRID VEHICLE CONTROL ECU ASSEMBLY WAS DEFECTIVE)