LANE DEPARTURE ALERT SYSTEM(w/ Dynamic Radar Cruise Control System) TERMINALS OF ECU


  1. CHECK LANE DEPARTURE WARNING CAMERA

    A000640E02
    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    T12-6 (CA1P) - T12-11 (GND) B - W-B CAN communication signal Power switch on (IG)

    Pulse generation

    (Waveform 1)
    T12-7 (IGB) - T12-11 (GND) V - W-B Power source Power switch on (IG) 11 to 14 V
    T12-11 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
    T12-12 (CA1N) - T12-11 (GND) W - W-B CAN communication signal Power switch on (IG)

    Pulse generation

    (Waveform 1)

    If the result is not as specified, there may be a malfunction on the wire harness side.

    Tech Tips

    Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


    1. A000513E02

      Waveform 1 (CAN communication signal)

      Item Content
      Terminal Name

      CH1: T12-6 (CA1P) - T12-11 (GND)

      CH2: T12-12 (CA1N) - T12-11 (GND)
      Tester Range 1 V/DIV., 50 μs./DIV.
      Condition Power switch on (IG)

      Tech Tips

      The waveform will vary depending on the content of the digital communication (digital signal).

  2. CHECK DRIVING SUPPORT ECU ASSEMBLY

    A0009MLE02

    Note


    • As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.

    • As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.

    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    H75-6 (SPSW) - H75-25 (GND) R - W-B Lane departure alert main switch signal Power switch on (IG), steering pad switch off 1 MΩ or higher
    Power switch on (IG), steering pad switch on (Lane departure alert main switch on) 228 to 252 Ω
    H75-17 (CA2L) - H75-25 (GND) LG - W-B CAN communication signal Power switch on (IG)

    Pulse generation

    (Waveform 1)
    H75-18 (CA1N) - H75-25 (GND) W - W-B CAN communication signal Power switch on (IG)

    Pulse generation

    (Waveform 2)
    H75-25 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
    H75-30 (B) - H75-25 (GND) V - W-B Power source Power switch on (IG) 11 to 14 V
    H75-39 (CA2H) - H75-25 (GND) R - W-B CAN communication signal Power switch on (IG)

    Pulse generation

    (Waveform 1)
    H75-40 (CA1P) - H75-25 (GND) B - W-B CAN communication signal Power switch on (IG)

    Pulse generation

    (Waveform 2)

    If the result is not as specified, there may be a malfunction on the wire harness side.

    Tech Tips

    Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


    1. A000513E02

      Waveform 1 (CAN communication signal)

      Item Content
      Terminal Name

      CH1: H75-39 (CA2H) - H75-25 (GND)

      CH2: H75-17 (CA2L) - H75-25 (GND)
      Tester Range 1 V/DIV., 50 μs./DIV.
      Condition Power switch on (IG)

      Tech Tips

      The waveform will vary depending on the content of the digital communication (digital signal).

    2. A000513E02

      Waveform 2 (CAN communication signal)

      Item Content
      Terminal Name

      CH1: H75-40 (CA1P) - H75-25 (GND)

      CH2: H75-18 (CA1N) - H75-25 (GND)
      Tester Range 1 V/DIV., 50 μs./DIV.
      Condition Power switch on (IG)

      Tech Tips

      The waveform will vary depending on the content of the digital communication (digital signal).

  3. CHECK SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

    A0006UTE02
    Text in Illustration
    *a

    Component without harness connected

    (Skid Control ECU (Brake Booster with Master Cylinder Assembly))

    		 - -
    Terminal No. (Symbol) Terminal Description
    A24-13 (BZ) Skid control buzzer assembly signal output

    1. TERMINAL INSPECTION


      1. Disconnect the connector and measure the voltage on the wire harness side.

        A0005CKE02
        Text in Illustration
        *a

        Front view of wire harness connector

        (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

        		 - -

        Tech Tips

        The voltage cannot be measured with the connector connected to the skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.

        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A24-13 (BZ) - Body ground B - Body ground Skid control buzzer assembly output Power switch on (IG), buzzer not sounding 11 to 14 V