Click here

DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:U0235

Click here
Click here
DTC Code DTC Name
U0235 Lost Communication with Cruise Control Front Distance Range Sensor
Click here

DESCRIPTION

The millimeter wave radar sensor and driving support ECU assembly transmit the data for general vehicle control and diagnosis function via CAN communication. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU assembly.

DTC No. DTC Detection Condition Trouble Area
U0235 While dynamic radar cruise control is either preparing for operation or operating and power switch is on (IG), communication between millimeter wave radar sensor and driving support ECU assembly stops for 1 second or more

  • Millimeter wave radar sensor assembly

  • Millimeter wave radar sensor circuit

  • Driving support ECU assembly
Click here

WIRING DIAGRAM

Click here

PROCEDURE


  1. Click here

    CHECK CAN COMMUNICATION SYSTEM


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Select "CAN Bus Check" from the "System Selection Menu" screen on the GTS.

    4. Select "Communication Malfunction DTC" from the "CAN Bus Check" screen, and then select "Enter".

      OK
      Communication system is normal.

    5. Turn the power switch off.


  2. Click here

    CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR POWER SOURCE)


    1. A0005RZE02

      Disconnect the A55 millimeter wave radar sensor assembly connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A55-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V
      Table 1. Text in Illustration
      *a

      Front view of wire harness connector

      (to Millimeter Wave Radar Sensor Assembly)

    4. Reconnect the A55 millimeter wave radar sensor assembly connector.


    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)


    1. Disconnect the A55 millimeter wave radar sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A55-2 (SGND) - Body ground Always Below 1 Ω
      Table 2. Text in Illustration
      *a

      Front view of wire harness connector

      (to Millimeter Wave Radar Sensor Assembly)

    3. Reconnect the A55 millimeter wave radar sensor assembly connector.


    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

    (Click here)


  5. Click here

    ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

    (Click here)


  6. Click here

    CHECK FOR DTCs (DTC U0235)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed for which cruise control operation is possible.

      2. Turn the cruise control switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC U0235 is output B

    7. Turn the power switch off.


    • A

      END

    • B

      REPLACE DRIVING SUPPORT ECU ASSEMBLY (Click here)