Click here

CRUISE CONTROL SYSTEM Cruise Control Switch Circuit

Click here
Click here
DTC Code DTC Name
  Cruise Control Switch Circuit
Click here

DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the power management control ECU reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions.

Click here

WIRING DIAGRAM

Click here

PROCEDURE


  1. Click here

    READ VALUE ON GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Cruise Control / Data List.

    5. Check the Data List to confirm proper functioning of the cruise control switch.

      Table 1. Text in Illustration
      *a ON-OFF
      *b -/SET
      *c +/RES
      *d CANCEL
      Table 2. Cruise Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main SW M-CPU Cruise control switch signal (Main CPU) / ON or OFF

      ON: Cruise control switch (ON-OFF button) pushed

      OFF: Cruise control switch (ON-OFF button) released

      		 -
      Cancel Switch CANCEL switch signal / ON or OFF

      ON: CANCEL switch on

      OFF: CANCEL switch off

      		 -
      SET/COAST Switch -/SET switch signal / ON or OFF

      ON: -/SET switch on

      OFF: -/SET switch off

      		 -
      RES/ACC Switch +/RES switch signal / ON or OFF

      ON: +/RES switch on

      OFF: +/RES switch off

      		 -
      OK
      When the cruise control switch is operated, the display changes as shown above.

    6. Turn the power switch off.


  2. Click here

    INSPECT CRUISE CONTROL SWITCH


    1. Remove the cruise control switch (Click here).

    2. A0003HDE05

      Measure the resistance according to the value(s) in the table below.

      Table 3. Text in Illustration
      *1 Cruise Control Switch (ON-OFF button) - -
      *a

      Component without harness connected

      (Cruise Control Switch)

      		 *b ON-OFF
      *c +/RES *d -/SET
      *e CANCEL - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 3 Cruise control switch ON-OFF button not pushed 1 MΩ or higher
      Cruise control switch ON-OFF button pushed Below 2.5 Ω
      +/RES 235 to 245 Ω
      -/SET 617 to 643 Ω
      CANCEL 1509 to 1571 Ω

    3. Reinstall the cruise control switch.


  3. Click here

    CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - CRUISE CONTROL SWITCH)


    1. Remove the cruise control switch wire.

    2. A00081WE02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      z6-3 - Cruise control switch side connector terminal 3 Always Below 1 Ω
      z6-4 - Cruise control switch side connector terminal 1 Always Below 1 Ω
      Table 4. Text in Illustration
      *a

      Front view of wire harness connector

      (to Spiral Cable with Sensor Sub-assembly)
      *b

      Front view of wire harness connector

      (to Cruise Control Switch)

    3. Reinstall the cruise control switch wire.


    • OKClick here
    • NG

      REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE

  4. Click here

    CHECK SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note:

    The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    Tip:

    1. A0004R1E09

      Remove the spiral cable with sensor sub-assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      z6-3 - H22-1 (CCS) Center 3 Ω or less
      2.5 rotations to the left
      2.5 rotations to the right
      z6-4 - H22-2 (ECC) Center 3 Ω or less
      2.5 rotations to the left
      2.5 rotations to the right

    3. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      z6-3 - H22-1 (CCS) Always 3 Ω or less
      z6-4 - H22-2 (ECC) Always 3 Ω or less
      Table 5. Text in Illustration
      *a

      Component without harness connected

      (Spiral Cable with Sensor Sub-assembly)
      Tip:

      The spiral cable with sensor sub-assembly makes a maximum of approximately 5 rotations.

    4. Reinstall the spiral cable with sensor sub-assembly.


  5. Click here

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)


    1. Disconnect the H2 power management control ECU connector.

    2. Disconnect the H22 spiral cable with sensor sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      H2-22 (CCS) - H22-1 (CCS) Always 3 Ω or less
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      H2-22 (CCS) or H22-1 (CCS) - Body ground Always 1 MΩ or higher

    4. Reconnect the H22 spiral cable with sensor sub-assembly connector.

    5. Reconnect the H2 power management control ECU connector.


    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)


    1. Disconnect the H22 spiral cable with sensor sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      H22-2 (ECC) - Body ground Always Below 1 Ω

    3. Reconnect the H22 spiral cable with sensor sub-assembly connector.


    • OK

      REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR