Click here

OIL AND OIL FILTER REPLACEMENT

Click here
Click here Click here

CAUTION / NOTICE / HINT

CAUTION:

  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water or waterless hand cleaner to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.

Click here

PROCEDURE


  1. Click here

    DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean the oil pan drain plug.

    4. Install the oil pan drain plug with a new gasket.

      40 N*m 408 kgf*cm 30 ft.*lbf
  2. Click here

    REMOVE OIL FILTER CAP ASSEMBLY


    1. A00069VE06

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

      Table 1. Text in Illustration
      *1 Pipe
      *2 Hose
    2. A0006PZ

      Remove the oil filter drain plug from the oil filter cap assembly.

    3. A0004QFE04

      Insert the pipe with the hose into the oil filter cap assembly.

      Table 2. Text in Illustration
      *1 Valve
      *2 Oil Filter Cap Assembly
      *3 O-ring
      *4 Pipe
      Note:

      If the O-ring is removed with the oil filter drain plug, install the O-ring together with the pipe.

      Tip:

      Use a container to catch the draining oil.

    4. A00092Z

      Check that the engine oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.

    5. A0004DQE03

      Using SST, remove the oil filter cap assembly.

      Table 3. Text in Illustration
      *1 Oil Filter Bracket Clip
      09228-06501
      Note:

      Do not remove the oil filter bracket clip.

    6. A0007JHE13

      Remove the oil filter element and O-ring from the oil filter cap assembly.

      Table 4. Text in Illustration
      *1 Oil Filter Element
      *2 Oil Filter Cap Assembly
      *3 O-ring
      Note:

      Be sure to remove the O-ring by hand, without using any tools, to prevent damage to the O-ring groove.

  3. Click here

    INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap assembly, threads and O-ring groove.

    2. A0004Q7E16

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

      Table 5. Text in Illustration
      *1 O-ring
      *a CORRECT
      *b INCORRECT
      Note:

      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element into the oil filter cap assembly.

    4. Remove all dirt and foreign matter from the installation surface and the inside of the oil filter cap assembly on the engine side.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap assembly.

      Note:

      Make sure that the O-ring does not get caught between the parts.

    6. A0004EEE06

      Using SST, tighten the oil filter cap assembly.

      Table 6. Text in Illustration
      *1 Oil Filter Cap Assembly
      *2 O-ring
      *3 Oil Filter Bracket
      *a No Gap
      09228-06501
      25 N*m 255 kgf*cm 18 ft.*lbf
      Note:

      After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

    7. A0004N0E04

      Apply a small amount of engine oil to a new O-ring, and install it to the oil filter cap assembly.

      Table 7. Text in Illustration
      *1 O-ring
      Note:

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap assembly.

    8. Install the oil filter drain plug.

      13 N*m 127 kgf*cm 10 ft.*lbf
      Note:

      Be careful that the O-ring does not get caught between any surrounding parts.

  4. Click here

    ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      • API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40

      • 20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill (with oil filter change) 4.4 liters (4.6 US qts, 3.9 Imp. qts)
      Drain and refill (without oil filter change) 4.0 liters (4.2 US qts, 3.5 Imp. qts)
      Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)

    2. Install the oil filler cap.

  5. Click here

    INSPECT FOR OIL LEAK

  6. Click here

    INSPECT ENGINE OIL LEVEL

    Click here