Click here

REAR AXLE HUB BOLT REPLACEMENT

Click here
Click here Click here

CAUTION / NOTICE / HINT

Note:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

Tip:

  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISABLE BRAKE CONTROL

    Click here

  3. Click here

    REMOVE REAR WHEEL

  4. Click here

    SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    1. A0008A7

      Remove the bolt and separate the rear flexible hose from the rear shock absorber.

    2. Remove the 2 bolts, and separate the rear disc brake caliper assembly.

      Note:

      Use wire or an equivalent tool to keep the rear disc brake caliper from hanging down by the flexible hose.

  5. Click here

    REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  6. Click here

    REMOVE REAR DISC

    Click here

  7. Click here

    REMOVE REAR AXLE HUB BOLT


    1. A0008I2E06

      Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

      Table 1. Text in Illustration
      *1 Service Nut
      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)
      Note:

      Install the service nuts to prevent damage to the rear axle hub bolts.

    2. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

      09611-12010
      Note:

      Do not damage the threads of the rear axle hub bolts.

  8. Click here

    INSTALL REAR AXLE HUB BOLT


    1. A0008V1E07

      Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

      Table 2. Text in Illustration
      *1 Service Nut
      *2 Washer

    2. Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)
      Tip:

      Recommended washer thickness is 5 mm (0.197 in.) or more.

    3. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

      Note:

      • Install the service nuts to prevent damage to the rear axle hub bolts.

      • Do not damage the threads of the rear axle hub bolts.

    4. Remove the 3 service nuts and washer from the 3 rear axle hub bolts.

  9. Click here

    INSTALL REAR DISC

    Click here

  10. Click here

    INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  11. Click here

    INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. Install the rear disc brake caliper assembly with the 2 bolts.

      78 N*m 799 kgf*cm 58 ft.*lbf

    2. Install the rear flexible hose to the rear shock absorber with the bolt.

      19 N*m 192 kgf*cm 14 ft.*lbf
  12. Click here

    CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the cable to the negative (-) auxiliary battery terminal (Click here).

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs (Click here).

  13. Click here

    ADJUST PARKING BRAKE

    (Click here)

  14. Click here

    INSTALL REAR WHEEL

    103 N*m 1049 kgf*cm 76 ft.*lbf