ROOF HEADLINING REASSEMBLY

Info Added 2017-10-06

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. INSTALL ROOF HEADLINING SUPPORT PLATE (w/ Intrusion Sensor)


    1. Align the markings on the roof headlining with the roof headlining support plate and install it using hot melt glue.

      A001W8HC01
      *a Marking - -

  2. INSTALL HEADLINING LIGHT CASE (w/ Map Light)


    1. Align the markings on the roof headlining with the headlining light case and install it using hot melt glue.

      A001SRFC01
      *a Marking - -

  3. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here

  4. INSTALL NO. 1 ROOF WIRE


    1. A001XNMC01
      B00497S Install in this Direction

      w/ Vanity Light:


      1. Turn the visor connectors approximately 90° clockwise to connect the visor connector as shown in the illustration.

        Tech Tips

        Use the same procedures for the opposite side.

    2. for TMMT Made:

      A001WGXC01
      *A w/ Rain Sensor *B w/ Lane Departure Alert System
      *C w/ Vanity Light - -
      *a Marking - -
      B004987 Double-sided Tape - -

      1. Apply double-sided tape as shown in the illustration.

        Note

        Apply the supports with uniform loading, and without protruding from the roof headlining markings.

      2. Line up the No. 1 roof wire positioning tape and the roof headlining markings.

      3. Align new pieces of each adhesive tapes with the markings of the roof headlining and install them.

        A001W0TC01
        *A w/ Vanity Light *B Rain Sensor
        *C w/ Lane Departure Alert System *D w/ Intrusion Sensor
        *E w/ Map Light - -

      4. Engage each guide.

    3. except TMMT Made:


      1. Line up the No. 1 roof wire positioning tape and the roof headlining markings.

      2. Align new pieces of each adhesive tapes with the markings of the roof headlining and install them.

        A001VZTC01
        *A w/ Rain Sensor *B w/ Vanity Light
        *a Clamp *b Guide

      3. Engage each guide.

      4. Engage each clamp.

  5. INSTALL ROOF SILENCER PAD (w/ Map Light)


    1. Align the markings on the roof headlining with the 2 roof silencer pads and install them using hot melt glue.

      A001X50C01
      *a Marking - -

  6. INSTALL NO. 2 ROOF SILENCER PAD (w/ Map Light)


    1. Align the markings on the roof headlining with the 2 No. 2 roof silencer pads and install them using hot melt glue.

      A001X0FC01
      *a Marking - -

  7. INSTALL ROOF HEADLINING FORMING PAD (w/ Map Light)


    1. Align the markings on the roof headlining with the 2 roof headlining forming pads and install them using hot melt glue.

      A001SMHC01
      *a Marking - -

  8. INSTALL NO. 1 ROOF SILENCER PAD (w/o Safety Connect System)


    1. Align the markings on the roof headlining with the No. 1 roof silencer pad and install it using hot melt glue.

      A001TZMC01
      *a Marking - -

  9. INSTALL NO. 1 ROOF SILENCER PAD (w/ Safety Connect System)


    1. Align a new No. 1 roof silencer pad with the silencer markings on the roof headlining and install the No. 1 roof silencer pad using double-sided tape.

      Tech Tips

      Peel off the backing paper from the double-sided tape before installing the No. 1 roof silencer pad.

      A001U8WC01
      *a Marking - -

  10. INSTALL NO. 3 ROOF SILENCER PAD (w/ Safety Connect System)


    1. Align the markings on the roof headlining with the No. 3 roof silencer pad and install it using hot melt glue.

      A001WI2C01
      *a Marking - -

  11. INSTALL NO. 4 ROOF SILENCER PAD (w/ Safety Connect System)


    1. Align the markings on the roof headlining with the No. 4 roof silencer pad and install it using hot melt glue.

      A001VFUC01
      *a Marking - -