REAR SEAT OUTER BELT ASSEMBLY REMOVAL

Info Added 2017-10-06

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system

Click here

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system

Click here

*1: When performing learning using the GTS.

Click here

*2: w/ Stop and start system

CAUTION:


  • B00495G

    Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    CAUTION:


    • B00497C

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an SRS part is accidentally deployed, it may cause a serious injury.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR SEAT ASSEMBLY

    Click here

  4. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

    Click here

  5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    Click here

  6. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

    Click here

  7. REMOVE SPARE WHEEL CUSHION (w/ Deck Board)

    Click here

  8. REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)

    Click here

  9. REMOVE DECK FLOOR BOX RH (w/ Deck Floor Box)

    Click here

  10. REMOVE REAR DOOR SCUFF PLATE

    Click here

  11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP

    Click here

  12. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

    Click here

  13. REMOVE REAR SEAT SIDE GARNISH

    Click here

  14. REMOVE DECK TRIM REAR COVER

    Click here

  15. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

    Click here

  16. REMOVE DECK TRIM SIDE COVER (w/ Cover)

    Click here

  17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY

    Click here

  18. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

    Click here

  19. REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for LH Side)


    1. A001Y11

      Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly LH.

    2. w/o Pretensioner:


      1. A001XZT

        Loosen the nut.

      2. A001XA3

        Remove the 3 bolts.

      3. Disengage the guides to remove the rear seat 3 point type outer belt assembly LH with bracket.

      4. A001SX6

        Remove the nut.

      5. Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.

    3. w/ Pretensioner:


      1. A001TEH

        Loosen the nut.

      2. A001XGA

        Remove the 3 bolts.

      3. Disengage the guides to separate the rear seat 3 point type outer belt assembly LH with bracket.

      4. A001Y8WC01
        *a Locking Button
        *b Protective Tape

        Disengage the clamp.

      5. Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

      6. A001WY9

        Remove the nut.

      7. Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.

  20. REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for RH Side)


    1. A001VFW

      Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly RH.

    2. w/o Pretensioner:


      1. A001WKM

        Loosen the nut.

      2. A001TF4

        Remove the 3 bolts.

      3. Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.

      4. A001WYW

        Remove the nut.

      5. Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.

    3. w/ Pretensioner:


      1. A001V36C01
        *a Locking Button
        *b Protective Tape

        Disengage the clamp.

      2. Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

      3. A001WKM

        Loosen the nut.

      4. A001T6A

        Remove the 3 bolts.

      5. Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.

      6. A001SYS

        Remove the nut.

      7. Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.