CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL

Info Added 2017-10-06

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system

Click here

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system

Click here

*1: When performing learning using the GTS.

Click here

*2: w/ Stop and start system

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B00495G

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    CAUTION:


    • B00497C

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an SRS part is accidentally deployed, it may cause a serious injury.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

    CAUTION:

    When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

    A001UZEC03
    B004987 Deployment Side

    Note

    When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.


    1. Check that the ignition switch off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B00497C
    3. A001WAFC01
      *a Airbag Connector
      *b Airbag Connector Lock
      *c Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock and disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    4. Using needle nose pliers, remove the pins from the clips.

      Note

      Do not damage the pins.

      A001XUIC01
      *1 Clip *2 Curtain Shield Airbag Clip Spacer
      *a Pin *b Claw (A)
      *c Claw (B) *d Spacer Location

    5. Using 2 screwdrivers, disengage the claws (A) of clips to separate the clips from the vehicle body as shown in the illustration.

      Tech Tips

      Separate the clips and curtain shield airbag assembly from the vehicle body as a unit.

    6. Disengage the claws (B).

    7. While holding the curtain shield airbag assembly, remove the 3 bolts and disengage the hooks to remove the curtain shield airbag assembly.

    8. Remove the clips and curtain shield airbag clip spacer from the curtain shield airbag assembly.