AIRBAG SYSTEM, Diagnostic DTC:B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, B1648/82, B167B/82, B167C/82

DTC Code	DTC Name
B1627/82	Lost communication with Side Airbag Sensor LH
B1628/82	Side Airbag Sensor Assembly LH Initialization Incomplete
B1637/82	Lost Communication with Rear Airbag Sensor LH
B1638/82	Rear Airbag Sensor Assembly LH Initialization Incomplete
B1647/82	Lost Communication with Side Satellite Sensor Bus LH
B1648/82	Side Satellite Sensor Bus LH Initialization Incomplete
B167B/82	Lost Communication with Front Door Pressure Sensor LH
B167C/82	Front Door Pressure Sensor LH Initialization Incomplete

DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

The door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	Test Mode / Check Mode
B1627/82	Lost communication with Side Airbag Sensor LH	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B1628/82	Side Airbag Sensor Assembly LH Initialization Incomplete	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B1637/82	Lost Communication with Rear Airbag Sensor LH	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B1638/82	Rear Airbag Sensor Assembly LH Initialization Incomplete	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B1647/82	Lost Communication with Side Satellite Sensor Bus LH	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B1648/82	Side Satellite Sensor Bus LH Initialization Incomplete	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B167B/82	Lost Communication with Front Door Pressure Sensor LH	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B167C/82	Front Door Pressure Sensor LH Initialization Incomplete	Any of the following conditions is met: The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). No. 1 side airbag sensor LH malfunction No. 2 side airbag sensor LH malfunction Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Floor wire Front door wire LH No. 1 side airbag sensor LH No. 2 side airbag sensor LH Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode

DTC Detection Conditions (B1627/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B1628/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B1637/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B1638/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B1647/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B1648/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B167B/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

DTC Detection Conditions (B167C/82):
		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6	Pattern 7	Pattern 8
Diagnosis Condition	Ignition switch ON	○	○	○	○	○	○	○	○
Malfunction Status	The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1)	○	-	-	-	-	-	-	-
	The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1)	-	○	-	-	-	-	-	-
	The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1)	-	-	○	-	-	-	-	-
	The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1)	-	-	-	○	-	-	-	-
	No. 1 side airbag sensor LH malfunction	-	-	-	-	○	-	-	-
	No. 2 side airbag sensor LH malfunction	-	-	-	-	-	○	-	-
	Door side airbag sensor LH malfunction	-	-	-	-	-	-	○	-
	Airbag sensor assembly malfunction	-	-	-	-	-	-	-	○
Detection Time		-	-	-	-	-	-	-	-
Number of Trips		1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip	1 trip

Tech Tips

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

PROCEDURE

CHECK CURRENT DTC

Check for current DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then ON again.
Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B167B, B167C and 82 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
Current DTC B1647, B1648 or 82 is output.	A
Current DTC B1628 is output.	B
Current DTC B1638 is output.	C
Current DTC B167B or B167C is output.	D
Current DTC B1627 is output.	E
Current DTC B1637 is output.	F
Current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B167B, B167C and 82 are not output.	G

CHECK HISTORY DTC Click here

CHECK CONNECTORS Click here

CHECK NO. 1 SIDE AIRBAG SENSOR LH Click here

CHECK NO. 2 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK CONNECTORS

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK

The connectors are properly connected.

Tech Tips

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

OK
The connectors are properly connected.

Check that the terminals of the connectors are not deformed or damaged.

OK
The terminals are not deformed or damaged.

Result

Proceed to
OK
NG

REPLACE WIRE HARNESS

CHECK FLOOR WIRE (OPEN)

w/o Dual-stage SRS

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

w/ Dual-stage SRS

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	*4	Service Wire
*a	Front view of wire harness connector (to Airbag Sensor Assembly)	*b	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-4 (BBL+) - M13-3 (BBL-)	Always	Below 1 Ω

Disconnect the service wire from connector B.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

Measure the resistance according to the value(s) in the table below.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	-	-
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)	-	-

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-4 (BBL+) - M13-3 (BBL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

Connect the cable to the negative (-) battery terminal.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	-	-
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)	-	-

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
M13-4 (BBL+) - Body ground	Ignition switch ON	Below 1 V
M13-3 (BBL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO GROUND)

Measure the resistance according to the value(s) in the table below.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	-	-
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)	-	-

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-4 (BBL+) - Body ground	Always	1 MΩ or higher
M13-3 (BBL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (OPEN)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*4	Service Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - M13-2 (BCL-)	Always	Below 1 Ω

Disconnect the service wire from connector C.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - M13-2 (BCL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Connect the cable to the negative (-) battery terminal.

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
M13-1 (BCL+) - Body ground	Ignition switch ON	Below 1 V
M13-2 (BCL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO GROUND)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - Body ground	Always	1 MΩ or higher
M13-2 (BCL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK WIRE HARNESS (OPEN)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Service Wire
*a	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to Door Side Airbag Sensor LH)

Connect the connectors that link the floor wire and front door wire LH.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - J5-1 (BDL-)	Always	Below 1 Ω

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (OPEN) Click here

CHECK WIRE HARNESS (SHORT)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - J5-1 (BDL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT) Click here

CHECK WIRE HARNESS (SHORT TO B+)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Connect the cable to the negative (-) battery terminal.

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
J5-2 (BDL+) - Body ground	Ignition switch ON	Below 1 V
J5-1 (BDL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT TO B+) Click here

CHECK WIRE HARNESS (SHORT TO GROUND)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - Body ground	Always	1 MΩ or higher
J5-1 (BDL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT TO GROUND) Click here

CHECK NO. 1 SIDE AIRBAG SENSOR LH

*A	w/o Dual-stage SRS
*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor RH
*2	Airbag Sensor Assembly

Connect the connectors to the No. 2 side airbag sensor LH, door side airbag sensor LH and airbag sensor assembly.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1647, B1648 or 82 is output.	A
DTC B1642, B1643 or 81 is output.	B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE NO. 1 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK NO. 2 SIDE AIRBAG SENSOR LH

*1 No. 2 Side Airbag Sensor RH

*2 No. 1 Side Airbag Sensor LH

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1647, B1648 or 82 is output.	A
DTC B1642, B1643 or 81 is output.	B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE NO. 2 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK DOOR SIDE AIRBAG SENSOR LH

*1 Door Side Airbag Sensor RH

*2 No. 2 Side Airbag Sensor LH

Interchange the door side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1647, B1648 or 82 is output.	A
DTC B1642, B1643 or 81 is output.	B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK FLOOR WIRE (SHORT TO GROUND)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - Body ground	Always	1 MΩ or higher
JM1-40 (BDL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
JM1-22 (BDL+) - Body ground	Ignition switch ON	Below 1 V
JM1-40 (BDL-) - Body ground	Ignition switch ON	Below 1 V

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (OPEN)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*5	Service Wire
*a	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Tech Tips

The service wire has already been inserted into connector B.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-)	Always	Below 1 Ω

Disconnect the service wire from connector B.

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK HISTORY DTC

Check for history DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
History DTC B1627 is not output.	A
History DTC B1627 is output.	B

CHECK NO. 1 SIDE AIRBAG SENSOR LH Click here

CHECK CONNECTORS

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK

The connectors are properly connected.

Tech Tips

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

Check that the terminals of the connectors are not deformed or damaged.

OK
The terminals are not deformed or damaged.

Result

Proceed to
OK
NG

REPLACE WIRE HARNESS

CHECK FLOOR WIRE (OPEN)

w/o Dual-stage SRS

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

w/ Dual-stage SRS

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 side airbag sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	*4	Service Wire
*a	Front view of wire harness connector (to Airbag Sensor Assembly)	*b	Front view of wire harness connector (to No. 1 side airbag sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-4 (BBL+) - M13-3 (BBL-)	Always	Below 1 Ω

Disconnect the service wire from connector B.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

Measure the resistance according to the value(s) in the table below.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	-	-
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)	-	-

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-4 (BBL+) - M13-3 (BBL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

Connect the cable to the negative (-) battery terminal.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	-	-
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)	-	-

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
M13-4 (BBL+) - Body ground	Ignition switch ON	Below 1 V
M13-3 (BBL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO GROUND)

Measure the resistance according to the value(s) in the table below.

*A	w/o Dual-stage SRS	*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor LH	*2	Airbag Sensor Assembly
*3	Floor Wire	-	-
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)	-	-

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-4 (BBL+) - Body ground	Always	1 MΩ or higher
M13-3 (BBL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (OPEN)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*4	Service Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - M13-2 (BCL-)	Always	Below 1 Ω

Disconnect the service wire from connector C.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - M13-2 (BCL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Connect the cable to the negative (-) battery terminal.

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
M13-1 (BCL+) - Body ground	Ignition switch ON	Below 1 V
M13-2 (BCL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO GROUND)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - Body ground	Always	1 MΩ or higher
M13-2 (BCL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK WIRE HARNESS (OPEN)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Service Wire
*a	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to Door Side Airbag Sensor LH)

Connect the connectors that link the floor wire and front door wire LH.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - J5-1 (BDL-)	Always	Below 1 Ω

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (OPEN) Click here

CHECK WIRE HARNESS (SHORT)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - J5-1 (BDL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT) Click here

CHECK WIRE HARNESS (SHORT TO B+)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Connect the cable to the negative (-) battery terminal.

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
J5-2 (BDL+) - Body ground	Ignition switch ON	Below 1 V
J5-1 (BDL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT TO B+) Click here

CHECK WIRE HARNESS (SHORT TO GROUND)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - Body ground	Always	1 MΩ or higher
J5-1 (BDL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT TO GROUND) Click here

CHECK NO. 1 SIDE AIRBAG SENSOR LH

*A	w/o Dual-stage SRS
*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor RH
*2	Airbag Sensor Assembly

Connect the connectors to the No. 2 side airbag sensor LH, door side airbag sensor LH and airbag sensor assembly.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1628 is output.	A
DTC B1623 is output.	B
DTCs B1623 and B1628 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE NO. 1 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK FLOOR WIRE (SHORT TO GROUND)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - Body ground	Always	1 MΩ or higher
JM1-40 (BDL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
JM1-22 (BDL+) - Body ground	Ignition switch ON	Below 1 V
JM1-40 (BDL-) - Body ground	Ignition switch ON	Below 1 V

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (OPEN)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*5	Service Wire
*a	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Tech Tips

The service wire has already been inserted into connector B.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-)	Always	Below 1 Ω

Disconnect the service wire from connector B.

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK NO. 1 SIDE AIRBAG SENSOR LH

*A	w/o Dual-stage SRS
*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor RH
*2	Airbag Sensor Assembly

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1627 is output.	A
DTC B1622 is output.	B
DTCs B1622 and B1627 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE NO. 1 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK HISTORY DTC

Check for history DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than history DTC B1637 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
History DTC B1637 is not output.	A
History DTC B1637 is output.	B

CHECK NO. 2 SIDE AIRBAG SENSOR LH Click here

CHECK CONNECTORS

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

OK

The connectors are properly connected.

Tech Tips

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

Check that the terminals of the connectors are not deformed or damaged.

OK
The terminals are not deformed or damaged.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (OPEN)

*1	No. 2 Side Airbag Sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*4	Service Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - M13-2 (BCL-)	Always	Below 1 Ω

Disconnect the service wire from connector C.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

*1	No. 2 side airbag sensor LH
*2	No. 1 Side Airbag Sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - M13-2 (BCL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

*1	No. 2 side airbag sensor LH
*2	No. 1 side airbag sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 side airbag sensor LH)

Connect the cable to the negative (-) battery terminal.

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
M13-1 (BCL+) - Body ground	Ignition switch ON	Below 1 V
M13-2 (BCL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO GROUND)

*1	No. 2 side airbag sensor LH
*2	No. 1 side airbag sensor LH
*3	Floor Wire
*a	Front view of wire harness connector (to No. 1 side airbag sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
M13-1 (BCL+) - Body ground	Always	1 MΩ or higher
M13-2 (BCL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FLOOR WIRE

CHECK NO. 1 SIDE AIRBAG SENSOR LH

*A	w/o Dual-stage SRS
*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor RH
*2	Airbag Sensor Assembly

Connect the connector to the No. 2 side airbag sensor LH.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1638 is output.	A
DTC B1633 is output.	B
DTCs B1633 and B1638 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE NO. 1 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK NO. 2 SIDE AIRBAG SENSOR LH

*1 No. 2 Side Airbag Sensor RH

*2 No. 1 Side Airbag Sensor LH

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1638 is output.	A
DTC B1633 is output.	B
DTCs B1633 and B1638 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE NO. 2 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK NO. 2 SIDE AIRBAG SENSOR LH

*1 No. 2 Side Airbag Sensor RH

*2 No. 1 Side Airbag Sensor LH

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1637 is output.	A
DTC B1632 is output.	B
DTCs B1632 and B1637 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE NO. 2 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK CONNECTORS

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the No. 2 side airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK

The connectors are properly connected.

Tech Tips

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the No. 2 side airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

Check that the terminals of the connectors are not deformed or damaged.

OK
The terminals are not deformed or damaged.

Result

Proceed to
OK
NG

REPLACE WIRE HARNESS

CHECK WIRE HARNESS (OPEN)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Service Wire
*a	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to Door Side Airbag Sensor LH)

Connect the connectors that link the floor wire and front door wire LH.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

Note

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - J5-1 (BDL-)	Always	Below 1 Ω

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (OPEN) Click here

CHECK WIRE HARNESS (SHORT)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - J5-1 (BDL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT) Click here

CHECK WIRE HARNESS (SHORT TO B+)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Connect the cable to the negative (-) battery terminal.

Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
J5-2 (BDL+) - Body ground	Ignition switch ON	Below 1 V
J5-1 (BDL-) - Body ground	Ignition switch ON	Below 1 V

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT TO B+) Click here

CHECK WIRE HARNESS (SHORT TO GROUND)

Door Side Airbag Sensor LH

No. 2 Side Airbag Sensor LH

Front view of wire harness connector

(to Door Side Airbag Sensor LH)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
J5-2 (BDL+) - Body ground	Always	1 MΩ or higher
J5-1 (BDL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

CHECK FLOOR WIRE (SHORT TO GROUND) Click here

CHECK NO. 2 SIDE AIRBAG SENSOR LH

*1 No. 2 Side Airbag Sensor RH

*2 No. 1 Side Airbag Sensor LH

Connect the connector to the door side airbag sensor LH.
Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B167B or B167C is output.	A
DTC B166D or B166E is output.	B
DTCs B166D, B166E, B167B and B167C are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE NO. 2 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK DOOR SIDE AIRBAG SENSOR LH

*1 Door Side Airbag Sensor RH

*2 No. 2 Side Airbag Sensor LH

Interchange the door side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B167B or B167C is output.	A
DTC B166D or B166E is output.	B
DTCs B166D, B166E, B167B and B167C are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK FLOOR WIRE (SHORT TO GROUND)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - Body ground	Always	1 MΩ or higher
JM1-40 (BDL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT TO B+)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
JM1-22 (BDL+) - Body ground	Ignition switch ON	Below 1 V
JM1-40 (BDL-) - Body ground	Ignition switch ON	Below 1 V

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (SHORT)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*a	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-)	Always	1 MΩ or higher

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK FLOOR WIRE (OPEN)

*1	Door Side Airbag Sensor LH
*2	No. 2 Side Airbag Sensor LH
*3	Front Door Wire LH
*4	Floor Wire
*5	Service Wire
*a	Front view of wire harness connector (to No. 2 Side Airbag Sensor LH)
*b	Front view of wire harness connector (to Front Door Wire LH)

Disconnect the floor wire connector from the front door wire LH.

Tech Tips

The service wire has already been inserted into connector B.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-)	Always	Below 1 Ω

Disconnect the service wire from connector B.

Result

Proceed to
OK
NG

REPLACE FRONT DOOR WIRE LH

REPLACE FLOOR WIRE

CHECK NO. 1 SIDE AIRBAG SENSOR LH

*A	w/o Dual-stage SRS
*B	w/ Dual-stage SRS
*1	No. 1 Side Airbag Sensor RH
*2	Airbag Sensor Assembly

Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1627 is output.	A
DTC B1622 is output.	B
DTCs B1622 and B1627 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE NO. 1 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here

CHECK NO. 2 SIDE AIRBAG SENSOR LH

*1 No. 2 Side Airbag Sensor RH

*2 No. 1 Side Airbag Sensor LH

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

Tech Tips

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

Result

Result	Proceed to
DTC B1637 is output.	A
DTC B1632 is output.	B
DTCs B1632 and B1637 are not output.	C

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.

REPLACE AIRBAG SENSOR ASSEMBLY Click here

REPLACE NO. 2 SIDE AIRBAG SENSOR LH Click here

USE SIMULATION METHOD TO CHECK Click here