REAR DOOR LOCK INSTALLATION

Info Added 2017-10-06

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL NO. 1 REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A005OQC

      Engage the guide to install the No. 1 rear door lock remote control cable assembly to the rear door lock with motor assembly.

    2. A005Q2MC01
      B00497S Install in this Direction

      Engage the claws as shown in the illustration.

  2. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. w/o Double Locking System:


      1. A005OOR

        Engage the guide to install the rear door inside locking cable assembly to the rear door lock with motor assembly.

      2. A005OKYC01
        B00497S Install in this Direction

        Engage the claws as shown in the illustration.

    2. w/ Double Locking System:


      1. A005OME

        Engage the guide to install the rear door inside locking cable assembly to the rear door lock with motor assembly.

      2. A005Q4PC01
        B00497S Install in this Direction

        Engage the claws as shown in the illustration.

  3. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. w/ Double Locking System:


      1. A005PJX

        Engage the guide to install the rear door lock remote control cable assembly to the rear door lock with motor assembly.

      2. A005QETC01
        B00497S Install in this Direction

        Engage the claw as shown in the illustration.

    2. w/ Double Locking System:


      1. A005PZ4

        Engage the guide to install the rear door lock remote control cable assembly to the rear door lock with motor assembly.

      2. A005PELC01
        B00497S Install in this Direction

        Engage the claw as shown in the illustration.

  4. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Note


    • When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

    • Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.


    1. Apply MP grease to the sliding parts of the rear door lock with motor assembly.

    2. When reusing the rear door lock with motor assembly:


      1. Install a new door lock wiring harness seal to the rear door lock with motor assembly.

    3. A005QCQC01
      B00497S Install in this Direction

      Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    4. Connect the connector.

  5. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

    Click here

  6. INSTALL REAR DOOR OUTSIDE HANDLE COVER

    Click here

  7. INSTALL REAR DOOR SERVICE HOLE COVER

    Click here

  8. INSTALL REAR DOOR TRIM BRACKET

    Click here

  9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  10. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

    Click here

  11. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  12. INSTALL REAR DOOR REAR FRAME BRACKET

    Click here

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  14. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  15. INSPECT POWER WINDOW OPERATION

    Click here