FRONT DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly LH)
      *b	Unlock
      *c	Lock

      Check the door lock motor operation (for Driver Side).

      
      

      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

         OK
         Battery Connection Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock Battery positive (+) → 9 (L) Battery negative (-) → 10 (UL) Set Battery positive (+) → 10 (UL) Battery negative (-) → 9 (L) Unset

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock with motor assembly LH.

   2. Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Lock 10 kΩ or higher 8 (LSSR) - 7 (E) Unlock Below 1 Ω 9 (L) - 10 (UL) Unset 10 kΩ or higher 9 (L) - 10 (UL) Set Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly LH.

   3. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly LH)
      *b	Unlock
      *c	Off
      *d	Lock

      Check the resistance of the lock and unlock switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (L) - 7 (E) Held to lock side Below 1 Ω 9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher 10 (UL) - 7 (E) Held to unlock side Below 1 Ω 10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock with motor assembly LH.

   4. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door lock motor (for Front Passenger Side).

      
      

      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

         OK
         Battery Connection Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         If the result is not as specified, replace the front door lock with motor assembly LH.

   5. Check the operation of the door unlock detection switch (for Front Passenger Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Lock 10 kΩ or higher 8 (LSSR) - 7 (E) Unlock Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly LH.

2. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door lock motor (for Front Passenger Side).

      
      

      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

         OK
         Battery Connection Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Locks Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlocks

         If the result is not as specified, replace the front door lock with motor assembly RH.

   2. Check the operation of the door unlock detection switch (for Front Passenger Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Locked 10 kΩ or higher 7 (LSSR) - 8 (E) Unlocked Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly RH.

   3. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly RH)
      *b	Unlock
      *c	Lock

      Check the door lock motor operation (for Driver Side).

      
      

      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

         OK
         Battery Connection Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Locks Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlocks Battery positive (+) → 6 (L) Battery negative (-) → 5 (UL) Sets Battery positive (+) → 5 (UL) Battery negative (-) → 6 (L) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock with motor assembly RH.

   4. Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Locked 10 kΩ or higher 7 (LSSR) - 8 (E) Unlocked Below 1 Ω 5 (UL) - 6 (L) Unset 10 kΩ or higher 5 (UL) - 6 (L) Set Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly RH.

   5. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly RH)
      *b	Unlock
      *c	Off
      *d	Lock

      Check the resistance of the lock and unlock switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (L) - 8 (E) Held to lock side Below 1 Ω 6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher 5 (UL) - 8 (E) Held to unlock side Below 1 Ω 5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock with motor assembly RH.

3. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor (for Driver Side).

      
      

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK
         Battery Connection Result Battery positive (+) → Terminal 4 (L) Battery negative (-) → Terminal 3 (UL) Locks Battery positive (+) → Terminal 3 (UL) Battery negative (-) → Terminal 4 (L) Unlocks Battery positive (+) → Terminal 2 (DL) Battery negative (-) → Terminal 1 (UNDL) Sets Battery positive (+) → Terminal 1 (UNDL) Battery negative (-) → Terminal 2 (DL) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock with motor assembly LH.

   2. Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Locked 10 kΩ or higher 8 (LSSR) - 7 (E) Unlocked Below 1 Ω 6 (DLSR) - 5 (E) Unset 10 kΩ or higher 6 (DLSR) - 5 (E) Set Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly LH.

   3. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly LH)
      *b	Lock
      *c	Unlock

      Check the operation of the door key lock and unlock switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (L) - 7 (E) Held to lock side Below 1 Ω 9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher 10 (UL) - 7 (E) Held to unlock side Below 1 Ω 10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock with motor assembly LH.

   4. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor (for Front Passenger Side).

      
      

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK
         Battery Connection Result Battery positive (+) → Terminal 4 (L) Battery negative (-) → Terminal 3 (UL) Locks Battery positive (+) → Terminal 3 (UL) Battery negative (-) → Terminal 4 (L) Unlocks Battery positive (+) → Terminal 2 (DL) Battery negative (-) → Terminal 1 (UNDL) Sets Battery positive (+) → Terminal 1 (UNDL) Battery negative (-) → Terminal 2 (DL) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock with motor assembly LH.

   5. Check the operation of the door unlock detection switch and double lock position switch (for Front Passenger Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Locked 10 kΩ or higher 8 (LSSR) - 7 (E) Unlocked Below 1 Ω 6 (DLSR) - 5 (E) Unset 10 kΩ or higher 6 (DLSR) - 5 (E) Set Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly LH.

4. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor (for Front Passenger Side).

      
      

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK
         Battery Connection Result Battery positive (+) → Terminal 2 (L) Battery negative (-) → Terminal 1 (UL) Locks Battery positive (+) → Terminal 1 (UL) Battery negative (-) → Terminal 2 (L) Unlocks Battery positive (+) → Terminal 4 (DL) Battery negative (-) → Terminal 3 (UNDL) Sets Battery positive (+) → Terminal 3 (UNDL) Battery negative (-) → Terminal 4 (DL) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock with motor assembly RH.

   2. Check the operation of the door unlock detection switch and double lock position switch (for Front Passenger Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Locked 10 kΩ or higher 7 (LSSR) - 8 (E) Unlocked Below 1 Ω 9 (DLSR) - 10 (E) Unset 10 kΩ or higher 9 (DLSR) - 10 (E) Set Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly RH.

   3. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor (for Driver Side).

      
      

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK
         Battery Connection Result Battery positive (+) → Terminal 2 (L) Battery negative (-) → Terminal 1 (UL) Locks Battery positive (+) → Terminal 1 (UL) Battery negative (-) → Terminal 2 (L) Unlocks Battery positive (+) → Terminal 4 (DL) Battery negative (-) → Terminal 3 (UNDL) Sets Battery positive (+) → Terminal 3 (UNDL) Battery negative (-) → Terminal 4 (DL) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock with motor assembly RH.

   4. Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Locked 10 kΩ or higher 7 (LSSR) - 8 (E) Unlocked Below 1 Ω 9 (DLSR) - 10 (E) Unset 10 kΩ or higher 9 (DLSR) - 10 (E) Set Below 1 Ω

         If the result is not as specified, replace the front door lock with motor assembly RH.

   5. 

      *a	Component without harness connected (Front Door Lock with Motor Assembly RH)
      *b	Lock
      *c	Unlock

      Check the operation of the door key lock and unlock switch (for Driver Side).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (L) - 8 (E) Held to lock side Below 1 Ω 6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher 5 (UL) - 8 (E) Held to unlock side Below 1 Ω 5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock with motor assembly RH.