STEERING COLUMN ASSEMBLY INSTALLATION

Info Added 2017-10-06

PROCEDURE


  1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  2. INSTALL STEERING COLUMN ASSEMBLY (for LHD)

    Note

    Make sure that the wire harness is not interfering with the steering column assembly.


    1. Install the steering column assembly with the bolt and 2 nuts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

    2. Connect each connector and engage each clamp to the steering column assembly.

    3. Engage the power steering ECU wire harness clamp.

    4. Connect the 2 power steering ECU connectors.

  3. INSTALL STEERING COLUMN ASSEMBLY (for RHD)

    Note

    Make sure that the wire harness is not interfering with the steering column assembly.


    1. Install the steering column assembly with the bolt and 2 nuts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

    2. Connect each connector and engage each clamp to the steering column assembly.

    3. Engage the power steering ECU wire harness clamp.

    4. Connect the 2 power steering ECU connectors.

  4. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A001YCSC02
      *a Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

    2. Connect the No. 2 steering intermediate shaft assembly to the steering column assembly.

    3. Install the bolt.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  5. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A001SESC02
      *a Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.

    2. Install the No. 2 steering intermediate shaft assembly to the steering gear assembly.

    3. Install the bolt.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  6. INSTALL COLUMN HOLE COVER SILENCER SHEET


    1. A001SVX

      Engage the 2 claws to install the column hole cover silencer sheet.

    2. A001V3TC01
      B00497S Engage in this direction

      Engage the claw to close the column hole cover silencer sheet.

  7. INSTALL STOP LIGHT SWITCH ASSEMBLY

    Click here

  8. INSTALL NO. 1 AIR DUCT (for LHD)


    1. Engage the 3 claws to install a new No. 1 air duct.

    2. Install the 2 bolts.

  9. INSTALL NO. 2 AIR DUCT (for RHD)


    1. Engage the 3 claws to install a new No. 2 air duct.

    2. Install the 2 bolts.

  10. INSTALL CONSOLE BOX INSERT (for LHD)

    Click here

  11. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

    Click here

  12. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the battery connected and the ignition switch ON.

    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


    1. A001SFFC01
      B00497S Install in this Direction

      Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly as shown in the illustration.

    2. Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

  13. INSTALL UPPER STEERING COLUMN COVER


    1. Engage the 2 claws and 4 clips to connect the upper steering column cover.

    2. A001VHMC01
      B00497S Install in this Direction

      Engage the claw to install the upper steering column cover as shown in the illustration.

  14. INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

    Note

    If the lower steering column cover sub-assembly is installed in the incorrect order, the parts may break.


    1. A001U3NC01
      B00497S Install in this Direction

      Engage the 3 claws to install the lower steering column cover sub-assembly as shown in the illustration.

    2. Engage the 4 claws.

    3. Install the 2 screws.

  15. INSTALL FUSE BOX OPENING COVER (w/o Knee Airbag)

    Click here

  16. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Knee Airbag)

    Click here

  17. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Knee Airbag)

    Click here

  18. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Knee Airbag)

    Click here

  19. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

    Click here

  20. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

    Click here

  21. INSTALL COWL SIDE TRIM BOARD LH (w/o Knee Airbag)

    Click here

  22. INSTALL FRONT DOOR SCUFF PLATE LH (w/o Knee Airbag)

    Click here

  23. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

    Click here

  24. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  25. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

  26. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  27. CHECK STEERING WHEEL CENTER POINT

  28. INSTALL HORN BUTTON ASSEMBLY

    Click here

  29. TORQUE SENSOR ZERO POINT CALIBRATION

    Click here