TRANSMISSION CONTROL CABLE INSTALLATION

Info Added 2017-10-06

PROCEDURE


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A001UNP

      Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. A001UBE

      Engage the guide to connect the transmission control cable assembly to vehicle body.

    3. Install the nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    4. A005OCL

      Install the transmission control cable assembly to the transmission control cable support with the nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    5. A005OD5C01
      *a P Position
      *b N Position

      Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

    6. Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

    7. Connect the transmission control cable assembly to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
    8. A005P4KC01
      B00497S Install in this Direction

      Connect the transmission control cable assembly to the floor shift shift lever assembly.

      Note

      Make sure that the transmission control cable assembly is securely locked.

    9. A005OPNC01
      B00497S Install in this Direction

      Connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

      Note


      • Before connecting the transmission control cable assembly, check that the park/neutral position switch and shift lever are in N.

      • Install the end of the transmission control cable assembly so that the lock piece faces the driver side.

      • Install the end of the transmission control cable assembly all the way to the base of the pin.

  2. ADJUST SHIFT LEVER POSITION

    Click here

  3. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR


    1. Install the front No. 1 floor heat insulator to the vehicle body with the 3 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

    Click here

  5. INSTALL FRONT FLOOR CENTER BRACE

    Click here

  6. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

  7. INSTALL ECM

    Click here

  8. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  9. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  10. INSTALL NO. 1 AIR CLEANER INLET

    Click here

  11. INSTALL RADIATOR COVER

    Click here

  12. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  13. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

    Click here

  14. INSTALL BATTERY

    Click here

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  16. INSPECT SHIFT LEVER POSITION

    Click here

  17. INSPECT FOR EXHAUST GAS LEAK

    Click here

    Tech Tips

    Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

    Click here

  18. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here

  19. INSTALL REAR ENGINE UNDER COVER LH

    Click here

  20. INSTALL NO. 1 ENGINE UNDER COVER

    Click here