MANUAL TRANSAXLE UNIT COMPONENTS
Info Added 2017-10-06 
ILLUSTRATION
| *1 | BACK-UP LIGHT SWITCH ASSEMBLY | *2 | BREATHER PLUG |
| *3 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY | *4 | CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
| *5 | CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY | *6 | CONTROL CABLE BRACKET ASSEMBLY |
| *7 | MANUAL TRANSMISSION DRAIN PLUG | *8 | MANUAL TRANSMISSION FILLER PLUG |
| *9 | NEUTRAL POSITION SWITCH | *10 | NO. 1 CLUTCH HOUSING COVER |
| *11 | RELEASE CYLINDER BLEEDER PLUG | *12 | RELEASE CYLINDER BLEEDER PLUG CAP |
| *13 | TRANSMISSION REVOLUTION SENSOR | *14 | WIRE HARNESS CLAMP BRACKET |
| *15 | CLUTCH TUBE BOOT | *16 | GASKET |
| *17 | SPACER | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with union nut wrench | ● | Non-reusable part |
 |
Clutch spline grease |  |
Adhesive 1344 |
 |
Gear oil | ★ | Precoated part |
ILLUSTRATION
| *1 | STRAIGHT PIN | *2 | PLUG |
| *3 | SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING | *4 | LOCK BALL PIN |
| *5 | TRANSMISSION CASE PLUG | *6 | REVERSE IDLER GEAR SHAFT BOLT |
| *7 | SHIFT DETENT BALL | *8 | SHIFT DETENT BALL COMPRESSION SPRING |
| *9 | SHIFT DETENT BALL PLUG | *10 | NO. 1 LOCK BALL ASSEMBLY |
| *11 | OUTER SHIFT LEVER E-RING | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1344 | |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | OUTER SELECT LEVER | *2 | OUTER SELECT LEVER OIL SEAL |
| *3 | INNER SELECT LEVER | *4 | INNER SELECT LEVER SET BOLT |
| *5 | REVERSE SHIFT ARM BRACKET ASSEMBLY | *6 | REVERSE SHIFT FORK SHAFT ASSEMBLY |
| *7 | REVERSE IDLER GEAR SUB-ASSEMBLY | *8 | REVERSE IDLER THRUST WASHER |
| *9 | REVERSE IDLER GEAR SHAFT | *10 | INPUT SHAFT ASSEMBLY |
| *11 | NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY | *12 | NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
| *13 | NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY | *14 | OUTPUT SHAFT ASSEMBLY |
| *15 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE) | *16 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE) |
| *17 | SHIFT AND SELECT LEVER SHAFT ASSEMBLY | *18 | SHIFT INTER LOCK PLATE |
| *19 | DIFFERENTIAL CASE ASSEMBLY | *20 | SLOTTED SPRING PIN |
| *21 | REVERSE SHIFT FORK | *22 | NO. 4 GEAR SHIFT FORK SHAFT |
| *23 | NO. 1 GEAR SHIFT HEAD | *24 | NO. 1 GEAR SHIFT FORK ASSEMBLY |
| *25 | NO. 3 GEAR SHIFT HEAD | *26 | NO. 3 REVERSE PRE-BALK HEAD |
| *27 | NO. 3 GEAR SHIFT FORK ASSEMBLY | *28 | NO. 2 GEAR SHIFT HEAD |
| *29 | SNAP RING | *30 | SPACER |
| *31 | NO. 2 REVERSE PRE-BALK HEAD | *32 | STRAIGHT PIN |
| *33 | BIMETAL FORMED BUSHING | *34 | TORSION SPRING |
| *35 | SHIFT LEVER STOPPER | *36 | NO. 2 GEAR SHIFT FORK ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | FRONT DRIVE SHAFT OIL SEAL RH | *2 | FRONT TRANSAXLE CASE OIL SEAL |
| *3 | TRANSMISSION MAGNET | *4 | OUTPUT SHAFT COVER |
| *5 | FRONT OUTPUT SHAFT BEARING (OUTER RACE) | *6 | FRONT DIFFERENTIAL CASE FRONT PLATE WASHER |
| *7 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) | *8 | FRONT TRANSAXLE CASE |
| *9 | TRANSMISSION OIL SEPARATOR | *10 | REVERSE RESTRICT PIN ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | INPUT SHAFT COVER | *2 | MANUAL TRANSMISSION CASE |
| *3 | MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY | *4 | NO. 1 OIL RECEIVER PIPE |
| *5 | OUTER NO. 1 SHIFT LEVER | *6 | OUTER SHIFT LEVER OIL SEAL |
| *7 | REAR INPUT SHAFT BEARING SHIM | *8 | REAR OUTPUT SHAFT BEARING (OUTER RACE) |
| *9 | FRONT DRIVE SHAFT OIL SEAL LH | *10 | TRANSMISSION OIL SEPARATOR |
| *11 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) | *12 | REAR OUTPUT SHAFT BEARING SHIM |
| *13 | FRONT DIFFERENTIAL CASE REAR PLATE WASHER | *14 | OUTER SHIFT LEVER SPACER |
| *15 | INNER NO. 1 SHIFT LEVER | *16 | INNER SHIFT LEVER SLOTTED SPRING PIN |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |