MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) COMPONENTS
Info Added 2017-10-06 
ILLUSTRATION
| *1 | NO. 1 ENGINE UNDER COVER | *2 | REAR ENGINE UNDER COVER LH |
| *3 | REAR ENGINE UNDER COVER RH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | MANUAL TRANSMISSION FILLER PLUG | *2 | MANUAL TRANSMISSION DRAIN PLUG |
| *3 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | COWL BODY MOUNTING REINFORCEMENT RH |
| *3 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL | *4 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
| *5 | WATER GUARD PLATE LH | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | COWL BODY MOUNTING REINFORCEMENT RH |
| *3 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL | *4 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
| *5 | WATER GUARD PLATE LH | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY CLAMP SUB-ASSEMBLY | *4 | ECM |
| *5 | NO. 1 AIR CLEANER INLET | *6 | RADIATOR COVER |
| *7 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *8 | NO. 2 EARTH WIRE |
| *9 | NECK | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | CLUTCH HOSE | *2 | CONTROL CABLE BRACKET ASSEMBLY |
| *3 | ENGINE MOUNTING BRACKET LH | *4 | NO. 1 HEATER BRACKET SUB-ASSEMBLY |
| *5 | WIRE HARNESS | *6 | WIRE HARNESS CLAMP BRACKET |
| *7 | TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR | *8 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) | *2 | FRONT FLOOR CENTER BRACE |
| *3 | COMPRESSION SPRING | *4 | EXHAUST PIPE GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
| *3 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *4 | NO. 2 ENGINE MOVING CONTROL ROD |
| *5 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *6 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
| *7 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | BLEEDER CLUTCH RELEASE TUBE | *2 | CLUTCH FLEXIBLE HOSE BRACKET |
| *3 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY | *4 | CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE |
| *5 | CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY | *6 | MANUAL TRANSAXLE ASSEMBLY |
| *7 | SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY | *8 | O-RING |
| *9 | CLUTCH TUBE BOOT | *10 | FLYWHEEL HOUSING SIDE COVER |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with union nut wrench | ● | Non-reusable part |
 |
Clutch spline grease |  |
Gear oil |
| ★ | Precoated part | *T1 | for Flange Bolt: 37 (377, 27) for Bolt with Washer: 33 (337, 24) |