ENGINE ASSEMBLY COMPONENTS
Info Added 2017-10-06 
ILLUSTRATION
| *1 | NO. 1 ENGINE UNDER COVER | *2 | REAR ENGINE UNDER COVER LH |
| *3 | REAR ENGINE UNDER COVER RH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | COWL BODY MOUNTING REINFORCEMENT RH |
| *3 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL | *4 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
| *5 | WATER GUARD PLATE LH | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | COWL BODY MOUNTING REINFORCEMENT RH |
| *3 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL | *4 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
| *5 | WATER GUARD PLATE LH | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY CLAMP SUB-ASSEMBLY | *4 | ECM |
| *5 | NO. 1 AIR CLEANER INLET | *6 | NO. 1 INTERCOOLER COOLING WATER HOSE |
| *7 | NO. 1 RADIATOR HOSE | *8 | NO. 2 RADIATOR HOSE |
| *9 | NO. 4 INTERCOOLER COOLING WATER HOSE | *10 | RADIATOR COVER |
| *11 | NO. 1 RELAY BLOCK COVER | *12 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for CVT | *B | for Manual Transaxle |
| *C | w/ Air Conditioning System | - | - |
| *1 | DISCHARGE HOSE SUB-ASSEMBLY | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | FUEL VAPOR FEED HOSE | *4 | INLET HEATER WATER HOSE |
| *5 | OUTLET HEATER WATER HOSE | *6 | SUCTION HOSE SUB-ASSEMBLY |
| *7 | UNION TO CONNECTOR TUBE HOSE | *8 | WATER HOSE |
| *9 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
for DENSO Made: Compressor oil ND-OIL 8 or equivalent for VALEO Made: Compressor oil VC100YF or equivalent |
- | - |
ILLUSTRATION
| *A | w/ Cover | - | - |
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 2WD | *B | for AWD |
| *1 | FRONT FLOOR CENTER BRACE | *2 | FRONT EXHAUST PIPE ASSEMBLY |
| *3 | NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) | *4 | COMPRESSION SPRING |
| *5 | EXHAUST PIPE GASKET | *6 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for CVT | *B | for Manual Transaxle |
| *C | w/ Air Conditioning System | - | - |
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH | *4 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
| *5 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *6 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
| *7 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH | *8 | AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
| *9 | NO. 2 EARTH WIRE | *10 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| *T1 | for DENSO Made: 9.8 N*m (100 kgf*cm, 87 in.*lbf) for VALEO Made: 5.4 N*m (55 kgf*cm, 48 in.*lbf) |
- | - |
ILLUSTRATION
| *A | w/ Air Conditioning System | *B | w/o Air Conditioning System |
| *1 | FAN AND GENERATOR V BELT | *2 | V-RIBBED BELT TENSIONER ASSEMBLY |
| *3 | GENERATOR ASSEMBLY | *4 | FLYWHEEL HOUSING UNDER COVER |
| *5 | COMPRESSOR WITH PULLEY ASSEMBLY | *6 | IDLER PULLEY BRACKET |
| *7 | IDLER PULLEY COVER PLATE | *8 | NO. 1 IDLER PULLEY |
| *9 | NO. 1 IDLER PULLEY SUB-ASSEMBLY | *10 | TERMINAL CAP |
| *11 | ENGINE WIRE | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for CVT | *B | for Type A |
| *C | for Type B | - | - |
| *1 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *2 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT |
| *3 | ENGINE WIRE | *4 | FLYWHEEL HOUSING SIDE COVER |
| *5 | TRANSMISSION CONTROL CABLE ASSEMBLY | *6 | WIRE HARNESS CLAMP BRACKET |
| *7 | CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY | *8 | FRONT DRIVE PLATE SPACER |
| *9 | REAR DRIVE PLATE SPACER | - | - |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for Type A |
| *C | for Type B | - | - |
| *1 | ENGINE WIRE | *2 | FLYWHEEL HOUSING SIDE COVER |
| *3 | FLYWHEEL SUB-ASSEMBLY | *4 | NO. 1 CLUTCH HOSE |
| *5 | TRANSMISSION CONTROL CABLE ASSEMBLY | *6 | WIRE HARNESS CLAMP BRACKET |
| *7 | MANUAL TRANSAXLE ASSEMBLY | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with a union nut wrench | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° |
- | - |