CAMSHAFT POSITION SENSOR INSTALLATION

PROCEDURE


  1. INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)


    1. Connect the camshaft position sensor connector to install the camshaft position sensor to the sensor wire.

    2. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

      Note

      If reusing the camshaft position sensor, be sure to inspect the O-ring.

    3. A005OWBC95
      *a Adhesive

      Apply adhesive to 2 or 3 threads of a new bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    4. A005OGUC01
      *a 10 mm Union Nut Wrench
      *b Torque Wrench Fulcrum Length

      Using SST and a 10 mm union nut wrench, install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

      SST
      09961-00950
      Torque:
      Specified tightening torque
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • If the camshaft position sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

        5.1 N*m (52 kgf*cm, 45 in.*lbf)

    5. Connect the sensor wire connector.

    6. Install the fuel vapor feed pipe to the cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    7. Connect the fuel tube sub-assembly to the hose clamp.

  2. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  3. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

    Click here

  4. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

  5. INSTALL COWL BODY MOUNTING REINFORCEMENT RH

    Click here

  6. INSTALL COWL BODY MOUNTING REINFORCEMENT LH

    Click here

  7. INSTALL WATER GUARD PLATE LH

    Click here

  8. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

    Click here

  9. INSTALL WINDSHIELD WIPER MOTOR AND LINK

    Click here

  10. INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)


    1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

      Note

      If reusing the camshaft position sensor, be sure to inspect the O-ring.

    2. A005OWBC95
      *a Adhesive

      Apply adhesive to 2 or 3 threads of a new bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • If the camshaft position sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.

    4. Connect the camshaft position sensor connector.

  11. INSPECT FOR ENGINE OIL LEAK

    Click here