BLACK OUT TAPE(for Rear Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here


  • Rear door glass sub-assembly

  • Rear door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE REAR ARMREST ASSEMBLY

    Click here

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

    Click here

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL

    Click here

  8. REMOVE REAR DOOR SERVICE HOLE COVER

    Click here

  9. REMOVE REAR DOOR PANEL PROTECTOR

    Click here

  10. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

    Click here

  11. REMOVE REAR DOOR GLASS RUN

    Click here

  12. DISCONNECT REAR DOOR WEATHERSTRIP

    Click here

  13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

    Click here

  14. REMOVE REAR DOOR QUARTER WINDOW GLASS

    Click here

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  16. REMOVE REAR DOOR FRAME GARNISH

    Click here

  17. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

    Tech Tips

    When removing the rear door lower outside stripe, heat the vehicle body and rear door lower outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Rear Door Lower Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006I36C23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the rear door lower outside stripe and vehicle body.

    2. B006J6S

      Pull back on one of the ends of the rear door lower outside stripe to remove it.

      Tech Tips

      When pulling on the rear door lower outside stripe, pull it parallel to the vehicle body.

  18. REMOVE REAR DOOR OUTSIDE STRIPE

    Tech Tips

    When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Rear Door Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006I36C23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the rear door outside stripe and vehicle body.

    2. B006HMB

      Pull back on one of the ends of the rear door outside stripe to remove it.

      Tech Tips

      When pulling on the rear door outside stripe, pull it parallel to the vehicle body.

  19. REMOVE REAR DOOR UPPER OUTSIDE STRIPE

    Tech Tips

    When removing the rear door upper outside stripe, heat the vehicle body and rear door upper outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Rear Door Upper Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006I36C23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the rear door upper outside stripe and vehicle body.

    2. B006IFF

      Pull back on one of the ends of the rear door upper outside stripe to remove it.

      Tech Tips

      When pulling on the rear door upper outside stripe, pull it parallel to the vehicle body.