BLACK OUT TAPE(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE FRONT ARMREST ASSEMBLY

    Click here

  5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  9. REMOVE FRONT DOOR VENT SEAL

    Click here

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

    Click here

  11. REMOVE FRONT DOOR PANEL PROTECTOR

    Click here

  12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  13. REMOVE FRONT DOOR NO. 3 SERVICE HOLE COVER

    Click here

  14. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  16. DISCONNECT FRONT DOOR WEATHERSTRIP

    Click here

  17. REMOVE FRONT DOOR GLASS RUN

    Click here

  18. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

    Click here

  19. REMOVE FRONT DOOR FIX WINDOW GLASS

    Click here

  20. REMOVE DOOR FRAME GARNISH

    Click here

  21. REMOVE FRONT DOOR REAR OUTSIDE STRIPE

    Tech Tips

    When removing the front door rear outside stripe, heat the vehicle body and front door rear outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Front Door Rear Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006I36C23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the front door rear outside stripe and vehicle body.

    2. B006I52

      Pull back on one of the ends of the front door rear outside stripe to remove it.

      Tech Tips

      When pulling on the front door rear outside stripe, pull it parallel to the vehicle body.

  22. REMOVE FRONT DOOR STRIPE

    Tech Tips

    When removing the front door stripe, heat the vehicle body and front door stripe using a heat light.

    Heating Temperature
    Item Temperature
    Front Door Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006I36C23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the front door stripe and vehicle body.

    2. B006HAQ

      Pull back on one of the ends of the front door stripe to remove it.

      Tech Tips

      When pulling on the front door stripe, pull it parallel to the vehicle body.

  23. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE

    Tech Tips

    When removing the front door lower outside stripe, heat the vehicle body and front door lower outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Front Door Lower Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006I36C23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the front door lower outside stripe and vehicle body.

    2. B006I7J

      Pull back on one of the ends of the front door lower outside stripe to remove it.

      Tech Tips

      When pulling on the front door lower outside stripe, pull it parallel to the vehicle body.