REAR BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. A003K82

      Install the rear bumper reinforcement sub-assembly with the 8 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  2. INSTALL REAR BUMPER SIDE SEAL LH


    1. B006IPHC01
      *1 Rear Bumper Side Clip

      Install the 3 clips.

    2. Install the rear bumper side seal LH with the rear bumper side clip.

  3. INSTALL REAR BUMPER SIDE SEAL RH

    Tech Tips

    Use the same procedure as for the LH side.

  4. INSTALL REAR BUMPER SIDE RETAINER LH


    1. B006HIFC02
      B006IFV Install in this Direction (1)
      B006IV0 Install in this Direction (2)

      Engage the guide as shown in the illustration.

    2. Engage the claw as shown in the illustration.

    3. B006J6ZC02
      B006IFV Install in this Direction

      Engage the 3 clips as shown in the illustration to install the rear bumper side retainer LH.

  5. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL NO. 3 REAR BUMPER PAD

    Tech Tips

    When installing the No. 3 rear bumper pad, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove any remaining double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new No. 3 rear bumper pad.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B006J4OC01
      *a Line

      Install the No. 3 rear bumper pad as shown in the illustration.

      Tech Tips


      • Install the No. 3 rear bumper pad along the line on the rear bumper cover.

      • Use the same procedure for the RH side and LH side.

  7. INSTALL NO. 4 REAR BUMPER PAD

    Tech Tips

    When installing the No. 4 rear bumper pad, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove any remaining double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new No. 4 rear bumper pad.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B006HXJC01
      *a Line

      Install the No. 4 rear bumper pad as shown in the illustration.

      Tech Tips


      • Install the No. 4 rear bumper pad along the line on the rear bumper cover.

      • Use the same procedure for the RH side and LH side.

  8. INSTALL NO. 2 REAR BUMPER PAD

    Tech Tips

    When installing the No. 2 rear bumper pad, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove any remaining double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new No. 2 rear bumper pad.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B006I5CC01
      *a Line

      Install the No. 2 rear bumper pad as shown in the illustration.

      Tech Tips


      • Install the No. 2 rear bumper pad along the line on the rear bumper cover.

      • Use the same procedure for the RH side and LH side.

  9. INSTALL NO. 1 REAR BUMPER PAD

    Tech Tips

    When installing the No. 1 rear bumper pad, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove any remaining double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new No. 1 rear bumper pad.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B006IARC01
      *a Line

      Install the No. 1 rear bumper pad as shown in the illustration.

      Tech Tips


      • Install the No. 1 rear bumper pad along the line on the rear bumper cover.

      • Use the same procedure for the RH side and LH side.

  10. INSTALL REAR BUMPER CENTER GUARD


    1. Engage the 14 claws.

      A003LGV

    2. Install the rear bumper center guard with the 2 screws.

      A003NNT

  11. INSTALL REAR BUMPER PLATE LH


    1. B006J0NC01
      *a Hook
      B006IFV Install in this Direction

      Engage the hook.

    2. Engage the 2 claws as shown in the illustration to install the rear bumper plate LH.

  12. INSTALL REAR BUMPER PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. INSTALL REAR BUMPER CENTER PAD

    Tech Tips

    When installing the 3 rear bumper center pads, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove any remaining double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from the 3 new rear bumper center pads.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B006I8OC01
      *a Line

      Install the 3 rear bumper center pads as shown in the illustration.

      Tech Tips

      Install the 3 rear bumper center pads along the line on the rear bumper cover.

  14. INSTALL NO. 3 LUGGAGE ROOM WIRE


    1. A003JW3

      Engage the 6 clamps to install the No. 3 luggage room wire.

  15. INSTALL REAR BUMPER ENERGY ABSORBER


    1. A003MUU

      Engage the 3 clamps.

    2. A003NKO

      Install the rear bumper energy absorber with the 2 screws.

  16. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Click here

  17. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Click here

  18. INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Click here

  19. INSTALL REAR CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Click here

  20. INSTALL REAR CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Click here

  21. INSTALL REAR SIDE ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Click here

  22. INSTALL REAR TURN SIGNAL LIGHT ASSEMBLY LH

    Click here

  23. INSTALL REAR TURN SIGNAL LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.