FRONT BUMPER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front bumper removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front bumper assembly

  • Ultrasonic sensor detection angle (w/ Intuitive Parking Assist System)

  • Ultrasonic sensor detection angle registration (w/ Intuitive Parking Assist System)

  • Intelligent clearance sonar system

  • Simple advanced parking guidance system

Click here

Change grille shutter control mode and/or perform initialization Grille Shutter system

Click here

Tech Tips

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Click here

PROCEDURE


  1. PRECAUTION


    1. Change the grille shutter control mode to maintenance mode.

      Click here

      Note

      Make sure to change the grille shutter control mode to maintenance mode to prevent the grill shutter from opening or closing when the power switch is off.

  2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))

    Tech Tips

    Perform this procedure only when replacement of the front bumper reinforcement sub-assembly is necessary.

    Click here

  3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))

    Tech Tips

    Perform this procedure only when replacement of the front bumper reinforcement sub-assembly is necessary.

    Click here

  4. REMOVE RADIATOR SUPPORT OPENING COVER


    1. B006IYQ

      Remove the 7 clips.

    2. B006HXGC01
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Disengage the 2 guides and remove the radiator support opening cover as shown in the illustration.

  5. REMOVE FRONT BUMPER ASSEMBLY


    1. B006IX1C01
      B006IOI Protective Tape

      Apply protective tape around the front bumper assembly as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    2. B006II2C01
      *1 Pin Hold Clip
      *a 90 deg
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Using a screwdriver, turn each pin 90 degrees and remove the 2 pin hold clips.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    3. B006HU2

      Remove the screw.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    4. B006I5Y

      Remove the 10 screws.

    5. B006H7QC01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the 3 claws as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    6. B006I9JC01
      B006IFV Remove in this Direction

      Pull back the side of the front bumper assembly and disconnect the connector.

      Note

      Do not apply excessive force when pulling back the front bumper assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    7. B006I59C01
      *A w/ Intuitive Parking Assist System
      *B w/ Toyota Safety Sense P

      w/ Intuitive Parking Assist System:


      1. Disconnect the connector.

    8. w/ Toyota Safety Sense P:


      1. Disconnect the connector.

    9. B006J94

      Remove the 4 clips.

    10. B006J5CC01
      B006IFV Remove in this Direction

      Remove the 2 bolts and front bumper assembly as shown in the illustration.