DATA LIST
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus:
for Main Body: Body Electrical / Main Body / Data List.
for HL AutoLeveling: Body Electrical / HL AutoLeveling / Data List. (w/o Adaptive High Beam System)
for AHS: Body Electrical / AHS / Data List. (w/ Adaptive High Beam System)
for Combination Meter: Body Electrical / Combination Meter / Data List.
for Plug-in Control: Powertrain / Plug-in Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Parking Brake SW | Parking brake switch signal | OFF or ON | OFF: Parking brake switch off ON: Parking brake switch on |
- |
| Dimmer SW | Dimmer switch high position signal | OFF or ON | OFF: Dimmer switch in low position ON: Dimmer switch in high or high flash position |
- |
| Passing Light SW | Dimmer switch high flash position (pass) signal | OFF or ON | OFF: Dimmer switch not in high flash position ON: Dimmer switch in high flash position |
- |
| Rear Fog Light SW | Fog light switch rear position signal | OFF or ON | OFF: Fog light switch off ON: Fog light switch in rear position |
w/ Rear Fog Light |
| Front Fog Light SW | Fog light switch front position signal | OFF or ON | OFF: Fog light switch off ON: Fog light switch in front position |
- |
| Auto Light SW | Light control switch AUTO position signal | OFF or ON | OFF: Light control switch not in AUTO position ON: Light control switch in AUTO position |
- |
| Head Light SW (Head) | Light control switch head position signal | OFF or ON | OFF: Light control switch not in head position ON: Light control switch in head position |
- |
| Head Light SW (Tail) | Light control switch tail position signal | OFF or ON | OFF: Light control switch not in tail or head position ON: Light control switch in tail or head position |
- |
| Insolation Amount of Solar Sensor RH | Solar sensor RH condition | 0 to 51100 or SensorFail | Condition can be displayed | - |
| Insolation Amount of Solar Sensor LH | Solar sensor LH condition | 0 to 51100 or SensorFail | Condition can be displayed | - |
| Light Sensor Illuminance | Light control sensor illuminance | 0 to 8191 lx or SensorFail | Value is output according to ambient light level | - |
| AUTO Light Status | Auto light control operation status | Not AUTO or AUTO | Not AUTO: Automatic light control not operating AUTO: Automatic light control operating |
- |
| Light Sensor Connection Status | Light control sensor connection status | OFF or ON | OFF: Automatic light control sensor has not been connected ON: Automatic light control sensor connected or has been connected |
- |
| Headlight Lighting Function | ECU which controls the lighting system | Main Body or Lighting Sys ECU | Main Body: Lighting system controlled by main body ECU (multiplex network body ECU) Lighting Sys ECU: Lighting system is controlled by No. 1 headlight ECU sub-assembly |
- |
| Sensitivity | Sensitivity of the automatic light control system | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Disp Ex ON Sen | Ambient brightness level required to dim display lights (combination meter, navigation display, etc.) | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Disp Ex OFF Sen | Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.) | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Follow Me Home Lighting Time | Follow me home lighting time | 30 s, 60 s, 90 s or 120 s | Customize setting displayed | w/ Follow Me Home System |
| The Number of DTC | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Signal Switch (Right) | Turn signal switch (right) signal | OFF or ON | OFF: Turn signal switch (right) off ON: Turn signal switch (right) on |
- |
| Turn Signal Switch (Left) | Turn signal switch (left) signal | OFF or ON | OFF: Turn signal switch (left) off ON: Turn signal switch (left) on |
- |
| Hazard Flasher Switch | Hazard warning signal switch signal | OFF or ON | OFF: Hazard warning signal switch off ON: Hazard warning signal switch on |
- |
| Turn Switch Signal (Full Turn) | Turn signal switch (full turn) signal | OFF or ON | OFF: Turn signal switch (left and right) off ON: Turn signal switch (left or right) on |
- |
| Lane Change Flashing Times Setting | Condition of the lane change flashing times | OFF, 3, 4, 5, 6 or 7 | Customize setting displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Charging Lid Switch Status | EV charger lid switch assembly status | OFF or ON | OFF: Charging port lid closed ON: Charging port lid open |
- |
| Charging Lid Lamp Status | Spot light assembly status | OFF, Fade Out or ON | OFF: Spot light assembly off Fade Out: Spot light assembly fading out ON: Spot light assembly on |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Headlight Low Beam State | Low beam headlight state | OFF or ON | OFF: Low beam headlights off ON: Low beam headlights on |
- |
| Headlight High Beam State | High beam headlight state | OFF or ON | OFF: High beam headlights off ON: High beam headlights on |
- |
| DRL Operating State | Daytime running light state | OFF or ON | OFF: Daytime running lights off ON: Daytime running lights on |
- |
| Clearance Light State | Clearance light state | OFF or ON | OFF: Clearance lights off ON: Clearance lights on |
- |
| Right Cornering Light State | Cornering light RH state | OFF or ON | OFF: Cornering light RH off ON: Cornering light RH on |
Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Left Cornering Light State | Cornering light LH state | OFF or ON | OFF: Cornering light LH off ON: Cornering light LH on |
Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| +B | No. 1 headlight ECU sub-assembly LH IG power supply voltage value | 0.00 to 19.75 V | 11.00 to 14.00 V | - |
| Height Sens Pw Supply Val | Rear height control sensor sub-assembly LH power supply value | 0.00 to 5.00 V | 4.61 to 5.00 V | - |
| Rr Height Sens Signal Val | Rear height control sensor sub-assembly LH signal value | 0.00 to 5.00 V | 0.50 to 4.50 V | Value changes according to vehicle height |
| Front Right Wheel Speed Value | Front right wheel speed | 0.00 to 260.00 km/h (162.00 mph) | Condition can be displayed | - |
| Front Left Wheel Speed Value | Front left wheel speed | 0.00 to 260.00 km/h (162.00 mph) | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed | 0.00 to 260.00 km/h (162.00 mph) | Condition can be displayed | - |
| Rear Height Adjust Value | Rear height adjustment off set value | 0 to 1023 | Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed) | - |
| Rear Height Adjust Valid Flag | Rear height adjustment range | Inval or Valid | Inval: Rear height control sensor sub-assembly LH value out of normal range Valid: Rear height control sensor sub-assembly LH value within normal range |
- |
| Init Writing Count | Number of times initialization performed | 0 to 255 | Number of times initialization performed | - |
| Sensor Initialization Hist | Sensor initialization history | not comp, 10%, 25%, 50%, 75%, 100% or complied | not comp: No. 1 headlight ECU sub-assembly LH not initialized after replacing 10%: Initialization completed when fuel tank was 10% full 25%: Initialization completed when fuel tank was 25% full 50%: Initialization completed when fuel tank was 50% full 75%: Initialization completed when fuel tank was 75% full 100%: Initialization completed when fuel tank was 100% full complied: ECU not replaced and ECU has not been initialized at workshop |
- |
| Steering Sensor Signal | Steering sensor value | -384.0 to 382.5 deg | Changes according to the operation of the steering wheel | - |
| Steering Sensor Center Position | Steering sensor center position | -3072.0 to 3070.5 deg | 0.0 deg | - |
| +B Voltage Value | No. 1 headlight ECU sub-assembly LH power supply voltage value | 0.00 to 19.75 V | 11.00 to 14.00 V | - |
| Leveling Motor Target Position | Headlight leveling motor target position | 0.0 to 102.3 % | 10 to 90 % | - |
| Number Of Trouble Codes | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Clearance Light State | Clearance light state | OFF or ON | OFF: Clearance lights off ON: Clearance lights on |
- |
| +B Voltage Value | No. 1 headlight ECU sub-assembly LH +B power supply voltage value | 0.00 to 19.75 V | 11.00 to 14.00 V | - |
| Traveling Direction | Traveling direction | Not Fwd or Fwd | Not Fwd: Shift lever in R or N position Fwd: Shift lever not in R or N position |
- |
| Steering Sensor Initialization Status | Steering sensor initialization state | Incomplete or Completed | Incomplete: Steering sensor zero point calibration incomplete Completed: Steering sensor zero point calibration complete |
- |
| Headlight Low Beam State | Low beam headlight state | OFF or ON | OFF: Low beam headlights off ON: Low beam headlights on |
- |
| Headlight High Beam State | High beam headlight state | OFF or ON | OFF: High beam headlights off ON: High beam headlights on |
- |
| DRL State | Daytime running light state | OFF or ON | OFF: Daytime running lights off ON: Daytime running lights on |
- |
| Engine | Ready signal | Stop or Run | Stop: Power switch not on (READY) Run: Power switch on (READY) |
- |
| Passing Light Switch | Dimmer switch high flash position (pass) signal | OFF or ON | OFF: Dimmer switch not in high flash position ON: Dimmer switch in high flash position |
- |
| Left and Right Leveling Motor Target Value (Integer) | Left and right headlight leveling motor target value (Integer) | 0 to 31 mm | Changes according to the position of the headlight leveling motor | - |
| Left and Right Leveling Motor Target Value (Fraction) | Left and right headlight leveling motor target value (Fraction) | 0.0000 to 0.9961 mm | Changes according to the position of the headlight leveling motor | - |
| Left Leveling Motor Current Value (Integer) | Current left headlight leveling motor target value (Integer) | 0 to 31 mm | Changes according to the position of the headlight leveling motor | - |
| Left Leveling Motor Current Value (Fraction) | Current left headlight leveling motor target value (Fraction) | 0.0000 to 0.9961 mm | Changes according to the position of the headlight leveling motor | - |
| Right Leveling Motor Current Value (Integer) | Current right headlight leveling motor target value (Integer) | 0 to 31 mm | Changes according to the position of the headlight leveling motor | - |
| Right Leveling Motor Current Value (Fraction) | Current right headlight leveling motor target value (Fraction) | 0.0000 to 0.9961 mm | Changes according to the position of the headlight leveling motor | - |
| +B | No. 1 headlight ECU sub-assembly LH IG power supply voltage value | 0.00 to 19.75 V | 11.00 to 14.00 V | - |
| Height Sens Pw Supply Val | Rear height control sensor sub-assembly LH power supply value | 0.00 to 6.25 V | 4.61 to 5.00 V | - |
| Rr Height Sens Signal Val | Rear height control sensor sub-assembly LH signal value | 0.00 to 5.00 V | 0.50 to 4.50 V | Value changes according to vehicle height |
| Steering Sens Signal | Steering sensor signal value | -384.0 to 382.5 deg | Changes according to the operation of the steering wheel | - |
| Steering Sens Center Pos | Steering sensor center position | -3072.0 to 3070.5 deg | 0.0 deg | - |
| FR Wheel Speed | Front right wheel speed | 0.00 to 327.67 km/h (203.60 mph) | Condition can be displayed | - |
| FL Wheel Speed | Front left wheel speed | 0.00 to 327.67 km/h (203.60 mph) | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed | 0.00 to 327.67 km/h (203.60 mph) | Condition can be displayed | - |
| Rear Height Adjust Valid Flag | Rear height adjustment range | Inval or Valid | Inval: Rear height control sensor sub-assembly LH value out of normal range Valid: Rear height control sensor sub-assembly LH value within normal range |
- |
| Init Writing Count | Number of times initialization performed | 0 to 255 | Number of times initialization performed | - |
| Sensor Initialization Hist | Sensor initialization history | not comp, 10%, 25%, 50%, 75%, 100% or complied | not comp: No. 1 headlight ECU sub-assembly LH not initialized after replacing 10%: Initialization completed when fuel tank was 10% full 25%: Initialization completed when fuel tank was 25% full 50%: Initialization completed when fuel tank was 50% full 75%: Initialization completed when fuel tank was 75% full 100%: Initialization completed when fuel tank was 100% full complied: ECU not replaced and ECU has not been initialized at workshop |
- |
| Number Of Trouble Codes | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus:
for Main Body: Body Electrical / Main Body / Active Test.
for HL AutoLeveling: Body Electrical / HL AutoLeveling / Active Test. (w/o Adaptive High Beam System)
for AHS: Body Electrical / AHS / Active Test. (w/ Adaptive High Beam System)
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Daytime Running Light | Daytime running lights | OFF or ON | - |
| Taillight Relay | Taillight relay | OFF or ON | - |
| Headlight Relay | Low beam headlights | OFF or ON | - |
| Head Light Hi | High beam headlights | OFF or ON | - |
| Front Fog Light Relay | Front fog lights | OFF or ON | Light control switch in tail position |
| Rear Fog Light Relay | Rear fog lights | OFF or ON |
|
| Dimmer Signal | Dimmer signal | OFF or ON | State where circumference illumination is bright |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Clearance Light | Clearance lights | OFF or ON | - |
| Headlight Low Beam | Low beam headlights | OFF or ON | - |
| Headlight High Beam | High beam headlights | OFF or ON | - |
| Daytime Running Light | Daytime running lights | OFF or ON | - |
| Cornering Light | Cornering lights | OFF or ON | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Headlight Indicator | "Headlight System Malfunction Visit Your Dealer" display | OFF or ON | - |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| High Beam Indicator | High beam indicator | OFF or ON | - |
| Clearance Light | Clearance lights | OFF or ON | - |
| Headlight Low Beam | Low beam headlights | OFF or ON | - |
| Headlight High Beam | High beam headlights | OFF or ON | - |
| Daytime Running Light | Daytime running lights | OFF or ON | - |
| Headlight Indicator | "Headlight System Malfunction Visit Your Dealer" display | OFF or ON | - |