FRONT DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive High Beam System
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here


  • Door window regulator sub-assembly

  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B006HTM

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    B006IKV

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. B006HNF

      Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug.

  4. REMOVE FRONT ARMREST ASSEMBLY


    1. B006IBYC01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the 3 clips and 7 claws as shown in the illustration.

    2. B006HPBC01
      B006IFV Remove in this Direction

      Disengage the guide to remove the front armrest assembly as shown in the illustration.

  5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)


    1. B006J4QC02
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the 2 clips and 4 claws as shown in the illustration.

    2. Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)


    1. B006IXKC01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the 2 clips and 4 claws as shown in the illustration.

    2. Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. B006HK8C01
      B006IOI Protective Tape

      Apply protective tape to the front door panel as shown in the illustration.

    2. B006ICK

      Remove the 3 screws.

    3. B006HDT

      Disengage the 2 clips.

    4. B006HEJ

      Using a clip remover, disengage the 10 clips.

    5. B006IVQ

      While pulling out the front door trim board sub-assembly, insert a hand between the front door trim board sub-assembly and front door panel up to the area where the claws are engaged.

    6. B006I1MC01
      B006J86 Place Hand Here

      While pulling down the part of the front door inner glass weatherstrip shown in the illustration, pull out the front door trim board sub-assembly to disengage the 2 claws.

    7. B006ICU

      Using a clip remover, disengage the clip.

    8. B006HNR

      Engage the 2 claws.

    9. B006HG7

      Pull out the front door trim board sub-assembly to disengage the guide from the front door panel.

    10. Lift the front door trim board sub-assembly to separate the front door trim board sub-assembly with the front door inner glass weatherstrip from the front door panel.

      Note

      To prevent damage to the guide, lift the front door trim board sub-assembly with the guide disengaged.

    11. B006HK9C01
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly
      B006IFV Remove in this Direction

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly as shown in the illustration.

  9. REMOVE FRONT DOOR VENT SEAL


    1. B006HPFC01
      B006IFV Remove in this Direction

      Remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. B006IVHC01
      B006IFV Remove in this Direction

      Slide the front door inner glass weatherstrip to remove it from the front door trim board sub-assembly as shown in the illustration.

  11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

    B006I9Z

    1. Disengage the 2 claws to remove the front door inside handle sub-assembly.

  12. REMOVE FRONT DOOR PANEL PROTECTOR

    Click here

  13. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  14. REMOVE FRONT DOOR NO. 3 SERVICE HOLE COVER


    1. B006J9N

      Remove the front door No. 3 service hole cover.

  15. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  16. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. B006J8V

      Turn each front door weatherstrip clip 45 degrees and remove the 3 front door weatherstrip clips as shown in the illustration.

    2. B006HLR

      Disengage the 4 clips to remove the front door service hole cover.

  17. REMOVE DOOR SIDE AIRBAG SENSOR

    Click here

  18. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. B006H87

      Remove the hole plug.

    2. for Driver Side:


      1. Connect the multiplex network master switch assembly.

    3. for Front Passenger Side:


      1. Connect the power window regulator switch assembly.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Turn the power switch on (IG).

    6. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

    9. for Driver Side:


      1. Disconnect the multiplex network master switch assembly.

    10. for Front Passenger Side:


      1. Disconnect the power window regulator switch assembly.

    11. B006HQT

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass sub-assembly to fall.

    12. B006IGUC01
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the front door glass sub-assembly.

  19. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. B006IWM

      Disengage the 2 claws to remove the front door No. 2 service hole cover.

    2. B006HH9C01
      *a Temporary Bolt

      Disconnect the connector.

    3. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

    4. Remove the 5 bolts.

    5. Remove the front door window regulator assembly.

    6. Remove the temporary bolt from the front door window regulator assembly.

  20. REMOVE FRONT DOOR GLASS RUN


    1. B006IK2

      Remove the front door glass run.

  21. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. B006IEJC01
      B006IFV Remove in this Direction

      Remove the bolt.

    2. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.

  22. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. B006IAW

      Disengage the 2 claws.

    2. Using a screwdriver, disconnect the connector.

    3. B006IGE

      Disengage the 3 clamps.

    4. B006ITMC01
      B006IFV Disengage in this Direction

      Disengage the 2 claws and move the lever as shown in the illustration.

    5. B006IH2C01
      B006IFV Remove in this Direction

      Remove the front door outside handle assembly as shown in the illustration.

  23. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. B006IW7

      Remove the hole plug.

    2. B006HEA

      Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.

  24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. B006IMI

      Remove the hole plug.

    2. B006IL8

      Using a T30 "TORX" socket wrench, loosen the screw.

    3. Disengage the 2 guides and claw and remove the front door outside handle cover.

  25. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    1. B006IMR

      Disengage the 3 claws to remove the front door front outside handle pad.

  26. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    1. B006J91

      Disengage the 3 guides and claw to remove the front door rear outside handle pad.

  27. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

    Click here

  28. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B006HCFC01
      *A Inside
      *B Outside

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Slide the front door outside handle frame sub-assembly to disengage the claw and remove the front door outside handle frame sub-assembly.

  29. REMOVE FRONT DOOR LOCK OPEN ROD


    1. B006HTWC01
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.

  30. REMOVE FRONT DOOR CHECK ASSEMBLY


    1. B006HK2

      Remove the 3 bolts and front door check assembly.

  31. REMOVE FRONT DOOR WEATHERSTRIP


    1. B006J7P

      Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.

  32. REMOVE DOOR FRAME GARNISH


    1. B006INN

      Disengage the 3 claws to remove the door frame garnish.

  33. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    1. B006J5XC01
      B006IR6 Bolt
      B006IKP Screw

      Remove the 3 bolts, screw and front door front lower frame sub-assembly.

  34. REMOVE FRONT DOOR FIX WINDOW GLASS


    1. B006IO4C01
      B006IFV Remove in this Direction

      Remove the front door fix window glass with front door fix window weatherstrip as shown in the illustration.

    2. Remove the front door fix window glass from the front door fix window weatherstrip.

  35. REMOVE FRONT DOOR PANEL CUSHION


    1. B006IAN

      Disengage the 4 claws to remove the 2 front door panel cushions.

  36. REMOVE FRONT DOOR DUST PROOF SEAL


    1. B006J79

      Disengage the 3 claws to remove the 3 front door dust proof seals.

  37. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

    Click here

  38. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

    Click here

  39. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

    Click here

  40. REMOVE FRONT DOOR REAR OUTSIDE STRIPE (w/ Black Out Tape)

    Click here

  41. REMOVE FRONT DOOR STRIPE (w/ Black Out Tape)

    Click here

  42. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE (w/ Black Out Tape)

    Click here

  43. REMOVE FRONT DOOR SCUFF PLATE

    Click here

  44. REMOVE COWL SIDE TRIM BOARD

    Click here

  45. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING

    Click here