POWER WINDOW CONTROL SYSTEM Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

Click here

WIRING DIAGRAM

A003OJGE69
*a Rear Power Window Regulator Switch Assembly (for LH Door)
*b Power Window Regulator Motor Assembly (for Rear LH Door)

CAUTION / NOTICE / HINT

Note


  • If the power window regulator motor assembly (for rear LH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that power window system customize settings "RL Window Auto Up" and "RL Window Auto Down" are set to "ON" before performing the following procedure.

    Click here

  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.

Tech Tips

If the pulse sensor built into the power window regulator motor assembly (for rear LH door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for LH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for LH door).

Click here

PROCEDURE


  1. READ VALUE USING GTS (RL-DOOR MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / RL-Door Motor / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > RL-Door Motor > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RL Door P/W Auto SW Rear LH door power window auto switch signal OFF or ON

      OFF: Rear LH door power window auto up or auto down switch not being operated

      ON: Rear LH door power window auto up or auto down switch being operated

      		 -

      Body Electrical > RL-Door Motor > Data List
      Tester Display
      RL Door P/W Auto SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) Click here

    OK

  2. PERFORM INITIALIZATION (FOR REAR LH DOOR)


    1. Initialize the power window regulator motor assembly (for rear LH door).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)


    1. Check that the rear LH door power window moves when the auto up and down functions of the rear power window regulator switch assembly (for LH door) are operated.

      Click here

      OK
      Rear LH door auto up and down functions are normal.
      Result
      Proceed to
      OK
      NG

    OK

    END (PROBLEM DUE TO INITIALIZATION FAILURE)

    NG

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) Click here

  4. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)


    1. Remove the rear power window regulator switch assembly (for LH door).

      Click here

    2. Inspect the rear power window regulator switch assembly (for LH door).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) Click here REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR))


    1. Disconnect the M2 power window regulator motor assembly (for rear LH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M3-8 (AUTO) - M2-4 (AUTO) Always Below 1 Ω
      M3-8 (AUTO) or M2-4 (AUTO) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR