AIR CONDITIONING SYSTEM, Diagnostic DTC:B1475/75

DTC Code DTC Name
B1475/75 A/C Inverter Cooling / Heating System Malfunction

DESCRIPTION

The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.

If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1475/75 A/C Inverter Cooling / Heating System Malfunction A/C inverter temperature outside specified range (temperature too high) or open or short to ground in temperature sensor circuit

  • Cooling fan system

  • Refrigerant volume

  • Compressor with motor assembly

  • CAN communication system

 Memorized

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

Note


  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Using the GTS, check if the CAN communication system is functioning normally.

      Click here

      Result
      Result Proceed to
      CAN communication system DTCs are not output A
      CAN communication system DTCs are output B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Air Conditioner > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Electrical Fan Control electric cooling fan motor OFF or ON

      Perform this test when the following conditions are met:


      • Power switch on (READY)

      Body Electrical > Air Conditioner > Active Test
      Tester Display
      Electrical Fan
      OK
      Electric cooling fan operates smoothly.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO COOLING FAN SYSTEM Click here

    OK

  3. CHECK REFRIGERANT PRESSURE


    1. Install a manifold gauge set.

      for HFC-134a (R134a): Click here

      for HFO-1234yf (R1234yf): Click here

    2. Turn the power switch on (READY).

    3. B006IDV

      Read the manifold gauge pressure when the following conditions are met.


      1. Prepare the vehicle according to the table below.

        Item Condition
        Vehicle doors Fully open
        Temperature setting MAX COLD
        Blower speed HI
        A/C switch On
        Recirculation/fresh switch RECIRCULATION
        Interior temperature 25 to 35°C (77 to 95°F)
      Standard Pressure
      Low pressure side
      150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
      High pressure side
      1470 to 1670 kPa (15 to 17 kgf/cm2, 213 to 242 psi)
      Result
      Result Proceed to
      OK A
      NG (for HFC-134a (R134a)) B
      NG (for HFO-1234yf (R-1234yf)) C

    B

    CHARGE REFRIGERANT Click here

    C

    CHARGE REFRIGERANT Click here

    A

  4. READ OUTPUT DTC (DTC B1475/75)


    1. Clear the DTCs.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    2. Turn the power switch on (READY).

    3. Prepare the vehicle according to the table below.

      Item Condition
      Blower speed HI
      A/C switch On
      Temperature setting MAX COLD

    4. Check for DTCs.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1475/75 is not output (normal) A
      DTC B1475/75 is output B

      Note

      If the engine idles continuously when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.


    A

    SYSTEM IS OK

    B

    REPLACE COMPRESSOR WITH MOTOR ASSEMBLY Click here