REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSPECT REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY

    Click here

  2. INSTALL REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH (for LH Side)


    1. A003MZWC03
      B006IR6 Bolt (A)
      B006IKP Bolt (B)

      Engage the 3 guides and temporarily install the rear 3 point type seat outer belt assembly LH with the 3 bolts.

    2. Uniformly tighten the 3 bolts in the order shown in the illustration to install rear 3 point type seat outer belt assembly LH.

      Torque:
      Bolt (A)
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Bolt (B)
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A003KFIC03
      *a Locking Button
      *b Lock

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    4. Check that the ELR locks.

      Note

      This check should be performed with the rear 3 point type seat outer belt assembly LH installed to the vehicle.


      1. With the rear 3 point type seat outer belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.

    5. A003LVTC01
      *a Protruding Part

      Install the floor anchor of the rear 3 point type seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear 3 point type seat outer belt assembly LH to overlap the protruding parts of the floor panel.

  3. INSTALL REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH (for RH Side)


    1. A003NCRC03
      *a Locking Button
      *b Lock

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    2. Engage the clamp.

    3. A003NLOC03
      B006IR6 Bolt (A)
      B006IKP Bolt (B)

      Engage the 3 guides and temporarily install the rear 3 point type seat outer belt assembly RH with the 3 bolts.

    4. Uniformly tighten the 3 bolts in the order shown in the illustration to install rear 3 point type seat outer belt assembly RH.

      Torque:
      Bolt (A)
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Bolt (B)
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    5. Check that the ELR locks.

      Note

      This check should be performed with the rear 3 point type seat outer belt assembly RH installed to the vehicle.


      1. With the rear 3 point type seat outer belt assembly RH installed to the vehicle, check that the belt locks when it is pulled out quickly.

    6. A003MCNC03
      *a Protruding Part

      Install the floor anchor of the rear 3 point type seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear 3 point type seat outer belt assembly RH to overlap the protruding parts of the floor panel.

  4. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY

    Click here

  5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY

    Click here

  6. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)

    Click here

  7. INSTALL ROPE HOOK (w/o Toyota Safety Sense)

    Click here

  8. INSTALL NO. 2 ROPE HOOK (w/o Toyota Safety Sense)

    Click here

  9. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Toyota Safety Sense)

    Click here

  10. INSTALL TONNEAU COVER HOOK A (w/ Toyota Safety Sense)

    Click here

  11. INSTALL REAR SEAT SIDE GARNISH

    Click here

  12. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY

    Click here

  13. INSTALL REAR UNDER SIDE COVER

    Click here

  14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

    Click here

  15. INSTALL REAR DOOR SCUFF PLATE

    Click here

  16. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  17. INSTALL REAR SEAT CUSHION ASSEMBLY LH (for LH Side)

    Click here

  18. INSTALL REAR SEAT CUSHION ASSEMBLY RH (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  19. INSTALL REAR SEATBACK ASSEMBLY LH (for LH Side)

    Click here

  20. INSTALL REAR SEATBACK ASSEMBLY RH (for RH Side)

    Click here

  21. INSTALL REAR SEATBACK HINGE COVER (for RH Side)

    Click here

  22. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

    Click here

  23. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

    Click here

  24. INSTALL REAR DECK TRIM COVER

    Click here

  25. INSTALL DECK TRIM SERVICE HOLE COVER

    Click here

  26. INSTALL DECK FLOOR BOX RH

    Click here

  27. INSTALL DECK FLOOR BOX LH

    Click here

  28. INSTALL REAR NO. 1 FLOOR BOARD

    Click here

  29. INSTALL REAR NO. 3 FLOOR BOARD

    Click here

  30. INSTALL REAR NO. 4 FLOOR BOARD

    Click here

  31. INSTALL REAR NO. 2 FLOOR BOARD

    Click here

  32. INSTALL TONNEAU COVER ASSEMBLY

    Click here

  33. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  34. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  35. INSPECT SRS WARNING LIGHT

    Click here