SIDE AIRBAG SENSOR(for Center Pillar) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the side airbag sensor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

*1: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B006HTM

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    B006IKV

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE

    Click here

  4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

    Tech Tips

    Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the lower center pillar garnish.

  5. REMOVE REAR DOOR SCUFF PLATE

    Click here

  6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

    Tech Tips

    Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the lower center pillar garnish.

  7. REMOVE LOWER CENTER PILLAR GARNISH

    Click here

  8. REMOVE SIDE AIRBAG SENSOR ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      B006IKV
    3. B006HOB

      Remove the bolt and disengage the claw to separate the side airbag sensor assembly.

    4. Disconnect the connector to remove the side airbag sensor assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        B006IYXC18
        *a White Housing Lock *b Yellow CPA
        *c Slide *d Push
      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    5. After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

      B006I7LC01
      *a Correct *b Incorrect
  9. REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY (w/ Airbag Cut Off Switch)


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      B006IKV
    3. Disconnect the connector from the side No. 2 airbag sensor assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        B006IAOC08
        *a White Housing Lock *b Yellow CPA
        *c Connector lock is released - -
      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    4. B006H6X

      Remove the bolt and disengage the claw to remove the side No. 2 airbag sensor assembly.

    5. Check that the position of the white housing lock is as shown in the illustration.

      B006I33C05
      *a Incorrect *b Correct