FRONT SEAT SIDE AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*2
Simple intelligent parking assist system*2
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Removal/installation of the front passenger seat*1 Zero point calibration (Occupant classification system)

  • Occupant classification system

  • Passenger airbag ON/OFF indicator

  • Airbag system (Front passenger side)

  • Seat belt warning system (Front passenger)

Click here

*1: w/ Occupant Classification System
*2: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

B006HTM

Note

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

for Manual Seat: Click here

for Power Seat: Click here

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

  2. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

    for Manual Seat: Click here

    for Power Seat: Click here

  3. REMOVE VERTICAL ADJUSTING HANDLE (for Driver Side Manual Seat)

    Click here

  4. REMOVE RECLINING HINGE COVER (for Manual Seat)

    Click here

  5. REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

    Click here

  6. REMOVE SEAT ADJUSTER COVER CAP (for Driver Side Manual Seat)

    Click here

  7. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD (for Power Seat)

    Click here

  8. REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)

    for Driver Side: Click here

    for Front Passenger Side: Click here

  9. REMOVE FRONT SEAT CUSHION SHIELD (for Power Seat)

    Click here

  10. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Manual Seat)

    for Driver Side: Click here

    for Front Passenger Side: Click here

  11. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Power Seat)

    Click here

  12. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

  13. REMOVE FRONT SEAT HEADREST SUPPORT

    for Manual Seat: Click here

    for Power Seat: Click here

  14. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

    for Manual Seat: Click here

    for Power Seat: Click here

  15. REMOVE FRONT SEAT AIRBAG ASSEMBLY

    CAUTION:

    When storing the front seat airbag assembly, keep the airbag deployment side facing upward.

    A003KO6C02
    B006IOI Deployment Side

    1. w/o Occupant Classification System:


      1. A003LRK

        Disengage the clamp.

      2. Remove the 2 nuts and front seat airbag assembly.

        Note


        • Do not reuse the nuts.

        • Make sure that the front seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.

    2. w/ Occupant Classification System:


      1. A003JZU

        Disengage the clamp.

      2. Remove the 2 nuts and front seat airbag assembly.

        Note


        • Do not reuse the nuts.

        • Make sure that the front seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.