AIRBAG SYSTEM, Diagnostic DTC:B1622/81, B1623/81, B1632/81, B1633/81, B1642/81, B1643/81, B166D/81, B166E/81

DTC Code DTC Name
B1622/81 Lost communication with Side Airbag Sensor RH
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete
B1632/81 Lost Communication with Rear Airbag Sensor RH
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete
B1642/81 Lost Communication with Side Satellite Sensor Bus RH
B1643/81 Side Satellite Sensor Bus RH Initialization Incomplete
B166D/81 Lost Communication with Front Door Pressure Sensor RH
B166E/81 Front Door Pressure Sensor RH Initialization Incomplete

DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH, side airbag sensor assembly RH and rear airbag sensor RH.

The door side airbag sensor RH, side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1622/81 Lost communication with Side Airbag Sensor RH

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B1632/81 Lost Communication with Rear Airbag Sensor RH

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B1642/81 Lost Communication with Side Satellite Sensor Bus RH

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B1643/81 Side Satellite Sensor Bus RH Initialization Incomplete

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B166D/81 Lost Communication with Front Door Pressure Sensor RH

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B166E/81 Front Door Pressure Sensor RH Initialization Incomplete

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

  • Side airbag sensor assembly RH malfunction

  • Rear airbag sensor RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Rear airbag sensor RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

 Does not apply to test/check mode

WIRING DIAGRAM

B006IR3E82
*a Side Airbag Sensor Assembly RH
*b Door Side Airbag Sensor RH
*c Rear Airbag Sensor RH
*d Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE


  1. CHECK CURRENT DTC


    1. Check for current DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips


      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

      • Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B166D, B166E and 81 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      Current DTC B1642, B1643 or 81 is output. A
      Current DTC B1623 is output. B
      Current DTC B1633 is output. C
      Current DTC B166D or B166E is output. D
      Current DTC B1622 is output. E
      Current DTC B1632 is output. F
      Current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B166D, B166E and 81 are not output. G

    B

    CHECK HISTORY DTC Click here

    C

    CHECK HISTORY DTC Click here

    D

    CHECK CONNECTORS Click here

    E

    CHECK SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    F

    CHECK REAR AIRBAG SENSOR RH Click here

    G

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  3. CHECK FLOOR WIRE (OPEN)


    1. B006IB9C21
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - N45-3 (BBR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FLOOR WIRE (SHORT)


    1. B006IPTC53
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - N45-3 (BBR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  5. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006IPTC53
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
      N45-3 (BBR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  6. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006IPTC53
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - Body ground Always 1 MΩ or higher
      N45-3 (BBR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  7. CHECK FLOOR WIRE (OPEN)


    1. B006HMZC23
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)

      Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - N45-2 (BCR-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  8. CHECK FLOOR WIRE (SHORT)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - N45-2 (BCR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  9. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
      N45-2 (BCR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  10. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - Body ground Always 1 MΩ or higher
      N45-2 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  11. CHECK WIRE HARNESS (OPEN)


    1. B006IR5C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the connectors that link the floor wire and front door wire RH.

    2. Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - J6-1 (BDR-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (OPEN) Click here

    OK

  12. CHECK WIRE HARNESS (SHORT)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - J6-1 (BDR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT) Click here

    OK

  13. CHECK WIRE HARNESS (SHORT TO B+)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - Body ground Power switch on (IG) Below 1 V
      J6-1 (BDR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT TO B+) Click here

    OK

  14. CHECK WIRE HARNESS (SHORT TO GROUND)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - Body ground Always 1 MΩ or higher
      J6-1 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT TO GROUND) Click here

    OK

  15. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. B006IFOC01
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the rear airbag sensor RH, door side airbag sensor RH and airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1642, B1643 or 81 is output. A
      DTC B1647, B1648 or 82 is output. B
      DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  16. CHECK REAR AIRBAG SENSOR RH


    1. B006HZAC02
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor Assembly RH

      Interchange the rear airbag sensor RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1642, B1643 or 81 is output. A
      DTC B1647, B1648 or 82 is output. B
      DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.


    B

    REPLACE REAR AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  17. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. B006IAPC02
      *1 Door Side Airbag Sensor LH
      *2 Rear Airbag Sensor RH

      Interchange the door side airbag sensor RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1642, B1643 or 81 is output. A
      DTC B1647, B1648 or 82 is output. B
      DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the door side airbag sensor RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  18. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - Body ground Always 1 MΩ or higher
      JN1-40 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  19. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - Body ground Power switch on (IG) Below 1 V
      JN1-40 (BDR-) - Body ground Power switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  20. CHECK FLOOR WIRE (SHORT)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - JN1-40 (BDR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  21. CHECK FLOOR WIRE (OPEN)


    1. B006IE0C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)
      *b

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

      Tech Tips

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - JN1-40 (BDR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  22. CHECK HISTORY DTC


    1. Check for history DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than history DTC B1622 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      History DTC B1622 is not output. A
      History DTC B1622 is output. B

    B

    CHECK SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    A

  23. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  24. CHECK FLOOR WIRE (OPEN)


    1. B006IB9C21
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - N45-3 (BBR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  25. CHECK FLOOR WIRE (SHORT)


    1. B006IPTC53
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - N45-3 (BBR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  26. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006IPTC53
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
      N45-3 (BBR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  27. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006IPTC53
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-4 (BBR+) - Body ground Always 1 MΩ or higher
      N45-3 (BBR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  28. CHECK FLOOR WIRE (OPEN)


    1. B006HMZC23
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)

      Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - N45-2 (BCR-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  29. CHECK FLOOR WIRE (SHORT)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - N45-2 (BCR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  30. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
      N45-2 (BCR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  31. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - Body ground Always 1 MΩ or higher
      N45-2 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  32. CHECK WIRE HARNESS (OPEN)


    1. B006IR5C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the connectors that link the floor wire and front door wire RH.

    2. Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - J6-1 (BDR-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (OPEN) Click here

    OK

  33. CHECK WIRE HARNESS (SHORT)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - J6-1 (BDR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT) Click here

    OK

  34. CHECK WIRE HARNESS (SHORT TO B+)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - Body ground Power switch on (IG) Below 1 V
      J6-1 (BDR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT TO B+) Click here

    OK

  35. CHECK WIRE HARNESS (SHORT TO GROUND)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - Body ground Always 1 MΩ or higher
      J6-1 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT TO GROUND) Click here

    OK

  36. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. B006IFOC01
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the rear airbag sensor RH, door side airbag sensor RH and airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1623 is output. A
      DTC B1628 is output. B
      DTCs B1623 and B1628 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  37. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - Body ground Always 1 MΩ or higher
      JN1-40 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  38. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - Body ground Power switch on (IG) Below 1 V
      JN1-40 (BDR-) - Body ground Power switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  39. CHECK FLOOR WIRE (SHORT)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - JN1-40 (BDR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  40. CHECK FLOOR WIRE (OPEN)


    1. B006IE0C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)
      *b

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

      Tech Tips

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - JN1-40 (BDR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  41. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. B006IFOC01
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1622 is output. A
      DTC B1627 is output. B
      DTCs B1622 and B1627 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  42. CHECK HISTORY DTC


    1. Check for history DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than history DTC B1632 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      History DTC B1632 is not output. A
      History DTC B1632 is output. B

    B

    CHECK REAR AIRBAG SENSOR RH Click here

    A

  43. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor assembly RH and rear airbag sensor RH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor assembly RH and rear airbag sensor RH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  44. CHECK FLOOR WIRE (OPEN)


    1. B006HMZC23
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)

      Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - N45-2 (BCR-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  45. CHECK FLOOR WIRE (SHORT)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - N45-2 (BCR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  46. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
      N45-2 (BCR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  47. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006HKNC01
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N45-1 (BCR+) - Body ground Always 1 MΩ or higher
      N45-2 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  48. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. B006IFOC01
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connector to the rear airbag sensor RH.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1633 is output. A
      DTC B1638 is output. B
      DTCs B1633 and B1638 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  49. CHECK REAR AIRBAG SENSOR RH


    1. B006HZAC02
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor Assembly RH

      Interchange the rear airbag sensor RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1633 is output. A
      DTC B1638 is output. B
      DTCs B1633 and B1638 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  50. CHECK REAR AIRBAG SENSOR RH


    1. B006HZAC02
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor Assembly RH

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the rear airbag sensor RH with LH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1632 is output. A
      DTC B1637 is output. B
      DTCs B1632 and B1637 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  51. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the rear airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the rear airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  52. CHECK WIRE HARNESS (OPEN)


    1. B006IR5C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the connectors that link the floor wire and front door wire RH.

    2. Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - J6-1 (BDR-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (OPEN) Click here

    OK

  53. CHECK WIRE HARNESS (SHORT)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - J6-1 (BDR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT) Click here

    OK

  54. CHECK WIRE HARNESS (SHORT TO B+)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - Body ground Power switch on (IG) Below 1 V
      J6-1 (BDR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT TO B+) Click here

    OK

  55. CHECK WIRE HARNESS (SHORT TO GROUND)


    1. B006I4VC15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J6-2 (BDR+) - Body ground Always 1 MΩ or higher
      J6-1 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE (SHORT TO GROUND) Click here

    OK

  56. CHECK REAR AIRBAG SENSOR RH


    1. B006HZAC02
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor Assembly RH

      Connect the connector to the door side airbag sensor RH.

    2. Interchange the rear airbag sensor RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B166D or B166E is output. A
      DTC B167B or B167C is output. B
      DTCs B166D, B166E, B167B and B167C are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.


    B

    REPLACE REAR AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  57. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. B006IAPC02
      *1 Door Side Airbag Sensor LH
      *2 Rear Airbag Sensor RH

      Interchange the door side airbag sensor RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B166D or B166E is output. A
      DTC B167B or B167C is output. B
      DTCs B166D, B166E, B167B and B167C are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the door side airbag sensor RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  58. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - Body ground Always 1 MΩ or higher
      JN1-40 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  59. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - Body ground Power switch on (IG) Below 1 V
      JN1-40 (BDR-) - Body ground Power switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  60. CHECK FLOOR WIRE (SHORT)


    1. B006J7MC20
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - JN1-40 (BDR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  61. CHECK FLOOR WIRE (OPEN)


    1. B006IE0C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH
      *4 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)
      *b

      Front view of wire harness connector

      (to Front Door Wire RH)

      Disconnect the floor wire connector from the front door wire RH.

      Tech Tips

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN1-22 (BDR+) - JN1-40 (BDR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  62. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. B006IFOC01
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1622 is output. A
      DTC B1627 is output. B
      DTCs B1622 and B1627 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  63. CHECK REAR AIRBAG SENSOR RH


    1. B006HZAC02
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor Assembly RH

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the rear airbag sensor RH with LH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1632 is output. A
      DTC B1637 is output. B
      DTCs B1632 and B1637 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here