AIRBAG SYSTEM, Diagnostic DTC:B162B/85, B162C/85

DTC Code DTC Name
B162B/85 Side Airbag Sensor Assembly No.2 Lost Communication (RH)
B162C/85 Side Airbag Sensor Assembly No.2 Initialization Error (RH)

DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and side No. 2 airbag sensor assembly RH.

The side No. 2 airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B162B/85 Side Airbag Sensor Assembly No.2 Lost Communication (RH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).

  • Side No. 2 airbag sensor assembly RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Side No. 2 airbag sensor assembly RH

  • Airbag sensor assembly

 Does not apply to test/check mode
B162C/85 Side Airbag Sensor Assembly No.2 Initialization Error (RH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).

  • Side No. 2 airbag sensor assembly RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Side No. 2 airbag sensor assembly RH

  • Airbag sensor assembly

 Does not apply to test/check mode

WIRING DIAGRAM

B006HS9E25
*a BFR+
*b BFR-
*c Side No. 2 Airbag Sensor Assembly RH
*d Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE


  1. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and side No. 2 airbag sensor assembly RH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and side No. 2 airbag sensor assembly RH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK FLOOR WIRE (OPEN)


    1. B006I9DC04
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 20 (BCR+) and 19 (BCR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N25-2 (BFR+) - N25-1 (BFR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE (SHORT)


    1. B006H9JC04
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N25-2 (BFR+) - N25-1 (BFR-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FLOOR WIRE (SHORT TO B+)


    1. B006H9JC04
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N25-2 (BFR+) - Body ground Power switch on (IG) Below 1 V
      N25-1 (BFR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  5. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B006H9JC04
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N25-2 (BFR+) - Body ground Always 1 MΩ or higher
      N25-1 (BFR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  6. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    1. B006IFOC02
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connector to the airbag sensor assembly.

    2. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B162B/85, B162C/85, B163B/86 and B163C/86 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B162B/85 or B162C/85 is output. A
      DTC B163B/86 or B163C/86 is output. B
      DTCs B162B/85, B162C/85, B163B/86 and B163C/86 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here