LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Power switch on (ACC) signal OFF or ON

      OFF: Power switch off

      ON: Power switch on (ACC)

      		 "ON" is also displayed for this item when the power switch is on (IG).
      IG SW Power switch on (IG) signal OFF or ON

      OFF: Power switch off

      ON: Power switch on (IG)

      		 "OFF" is also displayed for this item when the power switch is on (ACC).
      RR Door Courtesy SW Rear door courtesy light switch assembly RH signal OFF or ON

      OFF: Rear door RH closed

      ON: Rear door RH open

      		 -
      RL Door Courtesy SW Rear door courtesy light switch assembly LH signal OFF or ON

      OFF: Rear door LH closed

      ON: Rear door LH open

      		 -
      Back Door Courtesy SW Back door courtesy switch signal OFF or ON

      OFF: Back door closed

      ON: Back door open

      		 -
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch assembly RH signal OFF or ON

      OFF: Front door RH closed

      ON: Front door RH open

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly LH signal OFF or ON

      OFF: Front door LH closed

      ON: Front door LH open

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON

      OFF: Rear door RH locked

      ON: Rear door RH unlocked

      		 When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.
      RL-Door Lock Pos SW Rear door LH unlock detection switch signal OFF or ON

      OFF: Rear door LH locked

      ON: Rear door LH unlocked

      		 When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.
      Interior Light Control Operation of the illuminated entry system OFF or ON Customized value is displayed -
      I/L ON W/Door Key Unlock Function that turns on the interior lights when the doors are unlocked OFF or ON Customized value is displayed -
      Lighting Time Lighting time of the delay control function (illuminated entry system) 15 s, 7.5 s or 30 s Customized value is displayed -
      Room Light when Aprchd Function that turns on the interior lights when a key enters any actuation area OFF or ON Customized value is displayed -
      Inside Foot Light Function that turns on the footwell light* OFF or ON Customized value is displayed -
      I/L when ACC OFF Function that turns on the interior lights when the power switch is turned from on (ACC) or on (IG) to off OFF or ON Customized value is displayed -
      Light Control Function that dims the footwell lights when the power switch is on (IG) and the shift lever is moved to any position other than P* OFF or ON Customized value is displayed -

      • *: w/ Footwell Light

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system*1 OFF or ON Perform the Active Test with interior light door switch in the map light assembly in the DOOR position.
      Fr Foot Light Footwell light*2 OFF or ON -
      Relay for Interior Light Auto Cut Function DOME CUT relay OFF or ON

      When performing this Active Test, turn all the interior lights (except footwell lights) on.


      • OFF: DOME CUT relay on (interior lights (except footwell lights) turn on)

      • ON: DOME CUT relay off (interior lights (except footwell lights) turn off)

      • *1: Refer to System Description for the lights that are controlled by the illuminated entry system.

        Click here

      • *2: w/ Footwell Light


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Power/Engine SW Light Power switch illumination OFF or ON -