CAN COMMUNICATION SYSTEM Solar Charge ECU Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
Solar Charge ECU Communication Stop Mode

Any of the following conditions are met:


  • Communication stop for "Solar Charging Control" is indicated on the "Communication Bus Check" screen of the GTS.

    Click here

  • Communication stop history for "Solar Charging Control" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Solar Charging Control" is 6 or more.)

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Solar Charge ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here


  • Solar energy control unit branch line or connector

  • Power source circuit of solar energy control unit

  • Solar energy control unit ground circuit

  • Solar energy control unit

WIRING DIAGRAM

B006HSUE05

CAUTION / NOTICE / HINT

Note


  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the power switch on (IG) and wait at least approximately 15 seconds.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS LINES (SOLAR ENERGY CONTROL UNIT BRANCH LINE)


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. Disconnect the N71 solar energy control unit connector.

    3. B006HXUC02
      *a

      Front view of wire harness connector

      (to Solar Energy Control Unit)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N71-7 (CA1H) - N71-3 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
      Result
      Result
      OK
      NG

    NG

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SOLAR ENERGY CONTROL UNIT)

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. Disconnect the N73 solar energy control unit connector.

    2. B006IJCC01
      *a

      Front view of wire harness connector

      (to Solar Energy Control Unit)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N73-9 (E01) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

    3. Reconnect the cable to the negative (-) auxiliary battery terminal.

    4. B006J4EC01
      *a

      Front view of wire harness connector

      (to Solar Energy Control Unit)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N73-4 (AMD) - Body ground Power switch off 11 to 14 V
      N71-5 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
      N71-1 (IGCT) - Body ground Power switch on (IG) 11 to 14 V
      Result
      Result
      OK
      NG

    OK

    REPLACE SOLAR ENERGY CONTROL UNIT Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)