SOLAR CHARGING SYSTEM, Diagnostic DTC:P1EC700

DTC Code DTC Name
P1EC700 Solar Charging Battery Cell Low Voltage

DESCRIPTION

Refer to the description for DTC P1EC000.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate
P1EC700 Solar Charging Battery Cell Low Voltage

The difference in voltage between each solar battery block is exceeds the specified value due to an internal malfunction of the solar battery.

(2 trip detection logic)

  • Wire harness or connector

  • Solar energy control unit

  • Solar battery

Solar Charging Warning Light:

Comes on
Related Data List
DTC No. Data List
P1EC700

  • Solar Charging Battery Block 1 Voltage

  • Solar Charging Battery Block 2 Voltage

  • Solar Charging Battery Block 3 Voltage

  • Solar Charging Battery Block 1 Voltage Sensor Upper Side Voltage

  • Solar Charging Battery Block 1 Voltage Sensor Under Side Voltage

  • Solar Charging Battery Block 2 Voltage Sensor Upper Side Voltage

  • Solar Charging Battery Block 2 Voltage Sensor Middle Side Voltage

  • Solar Charging Battery Block 2 Voltage Sensor Under Side Voltage

  • Solar Charging Battery Block 3 Voltage Sensor Upper Side Voltage

  • Solar Charging Battery Block 3 Voltage Sensor Under Side Voltage

  • Solar Charging Battery Charging and Discharging Voltage

  • Solar Charging Battery Block Total Voltage
Reference Voltage
Data List Voltage
Solar Charging Battery Block 1 Voltage Approximately 8.2 V
Solar Charging Battery Block 2 Voltage Approximately 8.2 V
Solar Charging Battery Block 3 Voltage Approximately 8.2 V
Solar Charging Battery Block 1 Voltage Sensor Upper Side Voltage Approximately 4.1 V
Solar Charging Battery Block 1 Voltage Sensor Under Side Voltage approximately 4.1 V
Solar Charging Battery Block 2 Voltage Sensor Upper Side Voltage Approximately 2.7 V
Solar Charging Battery Block 2 Voltage Sensor Middle Side Voltage Approximately 2.7 V
Solar Charging Battery Block 2 Voltage Sensor Under Side Voltage Approximately 2.7 V
Solar Charging Battery Block 3 Voltage Sensor Upper Side Voltage Approximately 4.1 V
Solar Charging Battery Block 3 Voltage Sensor Under Side Voltage Approximately 4.1 V
Solar Charging Battery Charging and Discharging Voltage Approximately 24.5 V
Solar Charging Battery Block Total Voltage Approximately 24.5 V

CONFIRMATION DRIVING PATTERN

Tech Tips

After completing repairs, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here


  1. Park the vehicle in an area where the solar radiation will be steady.

    Weather Clear or mostly clear and sunny
    Time Between 11:00 and 14:00
    Place An area where sunlight strikes the solar roof directly

    Tech Tips


    • Make sure no part of the solar roof is shaded.

    • If the solar roof is dirty, clean it.

  2. Turn the power switch off and then disconnect the cable from the negative (-) auxiliary battery terminal.

  3. Wait for 5 seconds or more, then disconnect the power source connector and then all other low voltage connectors the solar energy control unit.

  4. Wait for 30 seconds or more, then connect the low voltage connectors of the solar energy control unit except the power source connector and then connect the power source connector.

  5. Connect the cable to the negative (-) auxiliary battery terminal.

  6. Turn the power switch on (IG), wait for 5 to 10 seconds, and then turn the power switch off.

    Tech Tips

    Make sure to turn the power switch off within 10 seconds.

  7. Wait for 20 minutes and then check for DTCs to check that no DTCs have been stored.

    Tech Tips


    • While waiting, the HV battery will be charged by the solar charging system. However, depending on certain conditions, charging may not be performed.

    • If the SOC of the HV battery is 90% or more, the HV battery will not be charged by the solar charging system.

    • If any of the following conditions is met, the HV battery will not be charged by the solar charging system:


      • The HV battery is charged via an external power source.

      • The power switch is on (ACC).

      • The power switch is on (IG).

      • The power switch is on (READY).

      • The HV battery heating system is operating.

      • The remote air conditioning system is operating.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P1EC000.

Click here

CAUTION / NOTICE / HINT

CAUTION:


  • B006HUP

    Before performing any of the following operations, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip.


    • Inspecting the high-voltage system.

    • Disconnecting the low voltage connector of the inverter with converter assembly.

    • Disconnecting the low voltage connector of the HV battery.

    • Disconnecting the low voltage connector of the electric vehicle charger assembly.

    • Disconnecting the low voltage connector of the solar energy control unit.

  • B006IQP

    To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

  • B006HQC

    After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • B006IVPC02
    *a Without waiting for 10 minutes

    After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE


  1. CHECK DTC OUTPUT (SOLAR CHARGING SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Solar Charging Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Solar Charging Control > Trouble Codes
      Result
      Result Proceed to
      Only DTC P1EC700 is output, or DTCs other than in the table below are also output. A
      Any of the DTCs in the table below are output. B
      Relevant DTC
      P1ECD16 Solar Charging Battery Control System Circuit Voltage Below Threshold
      P1ECF87 Lost Communication with Internal Control Module Solar Charger Battery Monitor Missing Message
      P1ED462 Solar Charging Battery Voltage Sensor Signal Compare Failure
      P1EDD13 Solar Charging Battery Voltage Sensor "A" Circuit Open
      P1EE213 Solar Charging Battery Voltage Sensor "B" Circuit Open
      P1EE713 Solar Charging Battery Voltage Sensor "C" Circuit Open

    5. Turn the power switch off.


    B

    GO TO DTC CHART (SOLAR CHARGING SYSTEM) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (SOLAR ENERGY CONTROL UNIT - SOLAR BATTERY)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the rear seat cushion assembly LH.

      Click here

    3. B006IB2N01

      Disconnect the N73 solar energy control unit connector.

    4. B006IM3N01

      Disconnect the N71 and N72 solar energy control unit connectors.

    5. Remove the No. 1 solar battery shield panel.

      Click here

    6. Disconnect the N70 solar battery connector.

    7. Measure the resistance according to the value(s) in the table below.

      B006ITHC07
      *a

      Rear view of wire harness connector

      (to Solar Energy Control Unit)

      		 *b

      Rear view of wire harness connector

      (to Solar Battery)
      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      N72-1 (VB3) - N70-9 (VB3) Power switch off Below 1 Ω
      N72-13 (VB2) - N70-7 (VB2) Power switch off Below 1 Ω
      N72-3 (VB1) - N70-16 (VB1) Power switch off Below 1 Ω
      N72-15 (GVB) - N70-18 (GVB) Power switch off Below 1 Ω
      N73-8 (GVBS) - N70-20 (GVBS) Power switch off Below 1 Ω
      N73-2 (VBS) - N70-10 (VBS) Power switch off Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      N72-1 (VB3) or N70-9 (VB3) - Body ground and other terminals Power switch off 10 kΩ or higher
      N72-13 (VB2) or N70-7 (VB2) - Body ground and other terminals Power switch off 10 kΩ or higher
      N72-3 (VB1) or N70-16 (VB1) - Body ground and other terminals Power switch off 10 kΩ or higher
      N72-15 (GVB) or N70-18 (GVB) - Body ground and other terminals Power switch off 10 kΩ or higher
      N73-8 (GVBS) or N70-20 (GVBS) - Body ground and other terminals Power switch off 10 kΩ or higher
      N73-2 (VBS) or N70-10 (VBS) - Body ground and other terminals Power switch off 10 kΩ or higher

    8. Reconnect the N70 solar battery connector.

    9. Install the No. 1 solar battery shield panel.

    10. Reconnect the N71 and N72 solar energy control unit connectors.

    11. Reconnect the N73 solar energy control unit connector.

    12. Install the rear seat cushion assembly LH.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (SOLAR ENERGY CONTROL UNIT - SOLAR BATTERY)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the rear seat cushion assembly LH.

      Click here

    3. B006IB2N01

      Disconnect the N73 solar energy control unit connector.

    4. B006IM3N01

      Disconnect the N71 and N72 solar energy control unit connectors.

    5. Remove the No. 1 solar battery shield panel.

      Click here

    6. Disconnect the N70 solar battery connector.

    7. Connect the cable to the negative (-) auxiliary battery terminal.

    8. Turn the power switch on (IG).

    9. Measure the voltage according to the value(s) in the table below.

      B006ITHC07
      *a

      Rear view of wire harness connector

      (to solar energy control unit)

      		 *b

      Rear view of wire harness connector

      (to Solar Battery)
      Standard Voltage
      Tester Connection Condition Specified Condition
      N72-1 (VB3) or N70-9 (VB3) - Body ground Power switch on (IG) Below 1 V
      N72-13 (VB2) or N70-7 (VB2) - Body ground Power switch on (IG) Below 1 V
      N72-3 (VB1) or N70-16 (VB1) - Body ground Power switch on (IG) Below 1 V
      N72-15 (GVB) or N70-18 (GVB) - Body ground Power switch on (IG) Below 1 V
      N73-8 (GVBS) or N70-20 (GVBS) - Body ground Power switch on (IG) Below 1 V
      N73-2 (VBS) or N70-10 (VBS) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) auxiliary battery terminal.

    12. Reconnect the N70 solar battery connector.

    13. Install the No. 1 solar battery shield panel.

    14. Reconnect the N71 and N72 solar energy control unit connectors.

    15. Reconnect the N73 solar energy control unit connector.

    16. Install the rear seat cushion assembly LH.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  4. CHECK SOLAR ENERGY CONTROL UNIT (+B SHORT)

    Result
    Proceed to
    OK
    NG

    1. Remove the No. 1 solar battery shield panel.

      Click here

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Disconnect the N70 solar battery connector.

    4. Turn the power switch on (IG).

    5. B006J1YC01
      *a

      Rear view of wire harness connector

      (to Solar Battery)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N70-9 (VB3) - Body ground Power switch on (IG) Below 1 V
      N70-7 (VB2) - Body ground Power switch on (IG) Below 1 V
      N70-16 (VB1) - Body ground Power switch on (IG) Below 1 V
      N70-18 (GVB) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    6. Turn the power switch off.

    7. Disconnect the cable from the negative (-) auxiliary battery terminal.

    8. Reconnect the N70 solar battery connector.

    9. Install the No. 1 solar battery shield panel.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SOLAR ENERGY CONTROL UNIT Click here

    OK

  5. CHECK SOLAR ENERGY CONTROL UNIT (VOLTAGE SENSOR)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the rear seat cushion assembly LH.

      Click here

    3. Connect the GTS to the DLC3.

    4. Turn the power switch on (IG).

    5. Enter the following menus: Powertrain / Solar Charging Control / Data List.


      Powertrain > Solar Charging Control > Data List
      Tester Display
      Solar Charging Battery Charging and Discharging Voltage
      Solar Charging Battery Block Total Voltage
      Solar Charging Battery Block 1 Voltage
      Solar Charging Battery Block 2 Voltage
      Solar Charging Battery Block 3 Voltage
      Solar Charging Battery Block 1 Voltage Sensor Upper Side Voltage
      Solar Charging Battery Block 1 Voltage Sensor Under Side Voltage
      Solar Charging Battery Block 2 Voltage Sensor Upper Side Voltage
      Solar Charging Battery Block 2 Voltage Sensor Middle Side Voltage
      Solar Charging Battery Block 2 Voltage Sensor Under Side Voltage
      Solar Charging Battery Block 3 Voltage Sensor Upper Side Voltage
      Solar Charging Battery Block 3 Voltage Sensor Under Side Voltage

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, ]other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    6. According to the display on the GTS, read the Data List.

    7. Turn the power switch off.

    8. Disconnect the N71 and N72 solar energy control unit connectors.

    9. Disconnect the N73 solar energy control unit connector.

    10. Compare the Data List values with those shown in the following combination table.

      B006IACC09
      *a

      Rear view of wire harness connector

      (to Solar Energy Control Unit)

      		 - -
      Specified Condition
      Tester Connection Tester Display Specified Condition
      N72-3 (VB1) - N72-15 (GVB) Solar Charging Battery Block 1 Voltage Difference between the value in the Data List and the actual measured value at the solar energy control unit connector is 0.1 V or less.
      N72-13 (VB2) - N72-3 (VB1) Solar Charging Battery Block 2 Voltage Difference between the value in the Data List and the actual measured value at the solar energy control unit connector is 0.1 V or less.
      N72-1 (VB3) - N72-13 (VB2) Solar Charging Battery Block 3 Voltage Difference between the value in the Data List and the actual measured value at the solar energy control unit connector is 0.1 V or less.
      N73-8 (GVBS) - N73-2 (VBS) Solar Charging Battery Charging and Discharging Voltage Difference between the value in the Data List and the actual measured value at the solar energy control unit connector is 0.3 V or less.
      N72-15 (GVB) - N72-1 (VB3) Solar Charging Battery Block Total Voltage Difference between the value in the Data List and the actual measured value at the solar energy control unit connector is 0.3 V or less.
      Condition (All of the following conditions are met.)
      "Solar Charging Battery Block 1 Voltage Sensor Upper Side Voltage" - "Solar Charging Battery Block 1 Voltage Sensor Under Side Voltage" = 0.2 V or less
      "Solar Charging Battery Block 2 Voltage Sensor Upper Side Voltage" - "Solar Charging Battery Block 2 Voltage Sensor Middle Side Voltage" = 0.2 V or less
      "Solar Charging Battery Block 2 Voltage Sensor Middle Side Voltage" - "Solar Charging Battery Block 2 Voltage Sensor Under Side Voltage" = 0.2 V or less
      "Solar Charging Battery Block 2 Voltage Sensor Upper Side Voltage" - "Solar Charging Battery Block 2 Voltage Sensor Under Side Voltage" = 0.2 V or less
      "Solar Charging Battery Block 3 Voltage Sensor Upper Side Voltage" - "Solar Charging Battery Block 3 Voltage Sensor Under Side Voltage" = 0.2 V or less
      "Solar Charging Battery Charging and Discharging Voltage" - "Solar Charging Battery Block Total Voltage" = 0.2 V or less

    11. Reconnect the N71 and N72 solar energy control unit connectors.

    12. Reconnect the N73 solar energy control unit connector.

    13. Install the rear seat cushion assembly LH.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SOLAR BATTERY Click here

    NG

    REPLACE SOLAR ENERGY CONTROL UNIT Click here

  6. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT

    NEXT

  7. CHECK SOLAR BATTERY (INTERNAL BLOCK VOLTAGE)

    Result
    Result Proceed to
    Difference between the highest block voltage and lowest block voltage is 1.2 V or more. A
    Other than above B

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the rear seat cushion assembly LH.

      Click here

    3. B006IB2N01

      Disconnect the N73 solar energy control unit connector.

    4. B006IM3N01

      Disconnect the N71 and N72 solar energy control unit connectors.

    5. Measure the voltage according to the value(s) in the table below.

      B006IACC07
      *a

      Rear view of wire harness connector

      (to Solar Energy Control Unit)

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      N72-1 (VB3) - N72-13 (VB2) Power switch off 6 to 10 V
      N72-13 (VB2) - N72-3 (VB1) Power switch off 6 to 10 V
      N72-3 (VB1) - N72-15 (GVB) Power switch off 6 to 10 V

    6. Reconnect the N71 and N72 solar energy control unit connectors.

    7. Reconnect the N73 solar energy control unit connector.

    8. Install the rear seat cushion assembly LH.

      Result
      Result Proceed to
      Difference between the highest block voltage and lowest block voltage is 1.2 V or more. A
      Other than above. B

    A

    REPLACE SOLAR BATTERY Click here

    B

    END

  8. REPLACE SOLAR ENERGY CONTROL UNIT

    Click here

    Result
    Proceed to
    NEXT

    NEXT

  9. CHECK SOLAR BATTERY (INTERNAL BLOCK VOLTAGE)

    Result
    Result Proceed to
    When the difference between maximum voltage and the minimum voltage of the solar battery block voltage is 1.2 V or more. A
    Other than above B

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the rear seat cushion assembly LH.

      Click here

    3. B006IB2N01

      Disconnect the N73 solar energy control unit connector.

    4. B006IM3N01

      Disconnect the N71 and N72 solar energy control unit connectors.

    5. Measure the voltage according to the value(s) in the table below.

      B006IACC07
      *a

      Rear view of wire harness connector

      (to Solar Energy Control Unit)

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      N72-1 (VB3) - N72-13 (VB2) Power switch off 6 to 10 V
      N72-13 (VB2) - N72-3 (VB1) Power switch off 6 to 10 V
      N72-3 (VB1) - N72-15 (GVB) Power switch off 6 to 10 V

    6. Reconnect the N71 and N72 solar energy control unit connectors.

    7. Reconnect the N73 solar energy control unit connector.

    8. Install the rear seat cushion assembly LH.

      Result
      Result Proceed to
      Difference between the highest block voltage and lowest block voltage is 1.2 V or more. A
      Other than above. B

    A

    REPLACE SOLAR BATTERY Click here

    B

    END