ULTRASONIC SENSOR(for Rear) INSTALLATION

PROCEDURE


  1. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

    • If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.


    1. Clean the surface of the rear bumper assembly.


      1. Remove any remaining double-sided tape from the rear bumper assembly.

      2. Wipe off any adhesive residue with cleaner.

    2. A003KOWC01
      *a 30 mm (1.18 in.)

      Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.

    3. Using a brush or felt, apply primer or equivalent to the 2 rear center ultrasonic sensor retainers installation area.

      A003OP2C01
      *a Line - -
      B006HNM Primer - -

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    4. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the 2 pieces of tape.

    5. Peel off the release paper from 2 new rear center ultrasonic sensor retainers.

    6. Align the 2 rear center ultrasonic sensor retainers with the mark on the rear bumper assembly and install it as shown in the illustration.

      A003LZIC01
      *a Line - -
      B006IOI Press area - -

      Note

      The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear center ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear center ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the rear center ultrasonic sensor retainer and rear bumper assembly.

  2. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

    • If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.

    • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. Clean the surface of the rear bumper assembly.


      1. Remove any remaining double-sided tape from the rear bumper assembly.

      2. Wipe off any adhesive residue with cleaner.

    2. A003KOWC01
      *a 25 mm (0.984 in.)

      Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.

    3. A003K8QC01
      *a Line
      B006HNM Primer

      Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    4. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.

    5. Peel off the release paper from a new rear corner ultrasonic sensor retainer.

    6. A003KUGC01
      *a Line
      B006IOI Press area

      Align the rear corner ultrasonic sensor retainer with the mark on the rear bumper assembly and install it as shown in the illustration.

      Note

      The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear corner ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear corner ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper assembly.

  3. INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

    • If a rear side ultrasonic sensor retainer has been removed, replace it with a new one.


    1. Clean the surface of the rear bumper assembly.


      1. Remove any remaining double-sided tape from the rear bumper assembly.

      2. Wipe off any adhesive residue with cleaner.

    2. A003KOWC01
      *a 30 mm (1.18 in.)

      Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.

    3. Using a brush or felt, apply primer or equivalent to the 2 rear side ultrasonic sensor retainers installation area.

      A003MZFC01
      *A for RH Side *B for LH Side
      *a Line - -
      B006HNM Primer - -

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    4. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the 2 pieces of tape.

    5. Peel off the release paper from 2 new rear side ultrasonic sensor retainers.

    6. Align the 2 rear side ultrasonic sensor retainers with the mark on the rear bumper assembly and install it as shown in the illustration.

      A003OXTC01
      *A for RH Side *B for LH Side
      *a Line - -
      B006IOI Press area - -

      Note

      The double-sided tape of a rear side ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear side ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear side ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the rear side ultrasonic sensor retainer and rear bumper assembly.

  4. INSTALL REAR CENTER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A003NSDC01
      B006IFV Install in this Direction

      Engage the 2 claws to install the rear center ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  5. INSTALL REAR CORNER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A003OIRC01
      B006IFV Install in this Direction

      Engage the 2 claws to install the rear corner ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  6. INSTALL REAR SIDE ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A003L7LC01
      B006IFV Install in this Direction

      Engage the 2 claws to install the rear side ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  7. INSTALL REAR BUMPER ASSEMBLY

    Click here

  8. PERFORM CALIBRATION

    Click here

    SST
    09989-00020