ULTRASONIC SENSOR(for Front) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Ultrasonic sensor*1

  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

  • Intelligent clearance sonar system

  • Toyota parking assist-sensor system

  • Simple intelligent parking assist system

Click here

Front bumper assembly

  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

  • Intelligent clearance sonar system

  • Simple intelligent parking assist system
Change grille shutter control mode and/or perform initialization Grille shutter system

Click here

*1: If a front side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform registration.

PROCEDURE


  1. REMOVE FRONT BUMPER ASSEMBLY

    Click here

  2. REMOVE FRONT SIDE ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A003MYY

      Disconnect the connector.

    2. B006J8IC01
      B006IFV Remove in this Direction

      Disengage the 2 claws and remove the front side ultrasonic sensor as shown in the illustration.

  3. REMOVE ULTRASONIC SENSOR CLIP

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. B006I0AC01
      B006IFV Remove in this Direction

      Disengage the clamp.

    2. Disengage the 4 claws and remove the ultrasonic sensor clip as shown in the illustration.

  4. REMOVE FRONT CORNER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A003M8R

      Disconnect the connector.

    2. B006IZ6C01
      B006IFV Remove in this Direction

      Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.

  5. REMOVE FRONT BUMPER PAD LH

    Click here

  6. REMOVE FRONT BUMPER PAD RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. REMOVE FRONT CENTER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A003KN6

      Disconnect the connector.

    2. B006IU7C01
      B006IFV Remove in this Direction

      Disengage the 2 claws and remove the front center ultrasonic sensor as shown in the illustration.

  8. REMOVE FRONT SIDE ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

    • When removing the front side ultrasonic sensor retainer, heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light.

    • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. Heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

      Heating Temperature
      Item Temperature
      Front Bumper Assembly 40 to 60°C (104 to 140°F)
      Front Side Ultrasonic Sensor Retainer

      CAUTION:


      • Do not touch the heat light and heated parts.

      • Touching the heat light may result in burns.

      • Touching heated parts for a long time may result in burns.

      B006I36C23
      *a Heated Part
      *b Heat Light
    2. A003LNC

      Remove the front side ultrasonic sensor retainer.

  9. REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

    • When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

    • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

      Heating Temperature
      Item Temperature
      Front Bumper Assembly 40 to 60°C (104 to 140°F)
      Front Corner Ultrasonic Sensor Retainer

      CAUTION:


      • Do not touch the heat light and heated parts.

      • Touching the heat light may result in burns.

      • Touching heated parts for a long time may result in burns.

      B006I36C23
      *a Heated Part
      *b Heat Light
    2. A003MQ1

      Remove the front corner ultrasonic sensor retainer.