INTELLIGENT CLEARANCE SONAR SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Initial Steering Angle Set Status of initial steering angle setting Not Yet or Done

      Not Yet: Not completed

      Done: Completed

      		 -
      Current Steering Angle Set Status of current steering angle setting Unset or Set

      Unset: Not completed

      Set: Completed

      		 -
      ICS SW Status Intelligent clearance sonar system switch assembly (Multi-information switch) OFF or ON

      OFF: Intelligent clearance sonar system off

      ON: Intelligent clearance sonar system on

      		 -
      Fr Sensor Onset Range Detection operation range (for front center sensors) Narrow or Wide

      Narrow: 600 mm (23.6 in.)

      Wide: 1000 mm (39.4 in.)

      		 Customized value displayed
      Rr Sensor Onset Range Detection operation range (for rear center sensors) Narrow or Wide

      Narrow: 600 mm (23.6 in.)

      Wide: 1500 mm (59.1 in.)

      		 Customized value displayed
      Keep Sense Buzzer Keep sense buzzer operation Not Avail or Avail

      Not Avail: Buzzer stops

      Avail: Buzzer sounds continuously

      		 Customized value displayed
      Fr & Rr Buzzer Volume Buzzer volume setting L, M1, M2, M3 or H

      L: Low volume

      M1: Medium low volume

      M2: Medium volume

      M3: Medium high volume

      H: High volume

      		 Customized value displayed
      Sensor Condition N Front sensor operation Not Avail or Avail

      Not Avail: Front sensors not available

      Avail: Front sensors available

      		 Customized value displayed
      Approach Display OFF Whether the display turns off after an obstacle is no longer detected. Not Avail or Avail

      Not Avail: Not displayed

      Avail: Displayed

      		 Customized value displayed
      Target 1 Distance (FLC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 1 Distance (FRC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 1 Distance (RLC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 1 Distance (RRC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 1 Distance (FL Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 1 Distance (FR Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 1 Distance (RL Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 1 Distance (RR Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 2 Distance (FLC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 2 Distance (FRC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 2 Distance (RLC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 2 Distance (RRC Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 7.65 m (0.00 to 25.09 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 7.65 m (0.00 to 25.09 ft.): Detected distance

      		 -
      Target 2 Distance (FL Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 2 Distance (FR Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 2 Distance (RL Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      Target 2 Distance (RR Sensor) Distance between ultrasonic sensor and target object Unknown, Not Detected or 0.00 to 5.10 m (0.00 to 16.73 ft.)

      Unknown: Detection conditions not met

      Not Detected: No objects detected

      0.00 to 5.10 m (0.00 to 16.73 ft.): Detected distance

      		 -
      ICS Function Current setting of intelligent clearance sonar system ON or OFF

      ON: Intelligent clearance sonar system enabled

      OFF: Intelligent clearance sonar system disabled

      		 Customized value displayed
      ICS System Existence of intelligent clearance sonar system Without or With

      Without: w/o Intelligent clearance sonar system

      With: w/ Intelligent clearance sonar system

      		 -
      ICS Stop Distance Target stop distance Short or Long

      Short: Near

      Long: Far

      		 Customized value displayed
      ICS SW Status Memory Setting that determines if the on/off operation state when the power switch is turned off is resumed when the power switch is turned on Yes or No

      Yes: Previous on/off operation state is resumed

      No: System operates when the power switch is turned on

      		 Customized value displayed
      Bumper Type Registered bumper type Unfixed or 1 to 127

      1: Standard

      2 to 127: Unknown

      Unfixed: Unknown

      		 -
      # Codes Number of stored DTCs min.: 0, max.: 255 Number of DTCs will be displayed -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

    5. According to the display on the GTS, perform the Active Test.


      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay Stop lights ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)

    6. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    7. According to the display on the GTS, perform the Active Test.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      ICS OFF Indicator ICS OFF indicator light ON / OFF -

    8. Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.

    9. According to the display on the GTS, perform the Active Test.


      Body Electrical > IPA/ICS/Clearance Sonar > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Front Buzzer No. 1 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the power switch is on (IG)
      Rear Buzzer No. 2 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the power switch is on (IG)