PARKING BRAKE CABLE(for Rear Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during No. 3 parking brake cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

  • Replacement of heated oxygen sensor (w/ Canister Pump Module)

  • Gas leak from exhaust system is repaired

 Inspection after repair

  • Poor idle, etc.

  • Engine start function, etc.

w/o Canister Pump Module: Click here

w/ Canister Pump Module: Click here

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

B006IQL

Tech Tips

Use the same procedure for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. LOOSEN NO. 1 WIRE ADJUSTING NUT

    for LHD:

    Click here

    for RHD:

    Click here

  3. REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Solar Charging System)

    Click here

  4. REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Solar Charging System)

    Click here

  5. REMOVE SOLAR BATTERY (w/ Solar Charging System)

    Click here

  6. REMOVE NO. 1 SOLAR BATTERY MOUNT BRACKET (w/ Solar Charging System)

    Click here

  7. REMOVE INVERTER BATTERY (w/ Canister Pump Module)

    Click here

  8. SEPARATE NO. 1 PARKING BRAKE CABLE ASSEMBLY

    Click here

  9. SEPARATE NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    1. B006I8A

      Separate the No. 1 parking brake pull rod sub-assembly from the No. 3 parking brake cable assembly as shown in the illustration.

  10. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

    Click here

  11. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR


    1. B006HMM

      Remove the 4 nuts and front No. 2 floor heat insulator.

  12. REMOVE REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

    w/o Canister Pump Module:

    Click here

    w/ Canister Pump Module:

    Click here

  13. REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

    w/o Canister Pump Module:

    Click here

    w/ Canister Pump Module:

    Click here

  14. REMOVE PARKING BRAKE LEVER PROTECTOR


    1. B006I2Q

      Remove the parking brake lever protector from the No. 3 parking brake cable assembly.

  15. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. Remove the 4 bolts and nut, and separate the No. 3 parking brake cable assembly.

      B006IFS
    2. B006HHY

      Pull out the No. 3 parking brake cable assembly to the outside of the vehicle body.

    3. w/ Clip:


      1. B006IT4C02
        *a Clip

        Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

        Note


        • Do not remove the clip from the No. 3 parking brake cable assembly.

        • If the clip is removed from the No. 3 parking brake cable assembly, make sure to replace it with a new one.

      2. B006HIOC03
        *1 Rear Disc Brake Cylinder Assembly
        *a Clip

        Disengage the clip and remove the No. 3 parking brake cable assembly.

    4. w/o Clip:


      1. B006IJV

        Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

      2. B006I4LC02
        *1 Rear Disc Brake Cylinder Assembly
        *a Clip

        Disengage the clip and remove the No. 3 parking brake cable assembly.