REAR BRAKE REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

*1: When performing learning using the GTS.
Click here Click here

Note


  • Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

  • After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISABLE BRAKE CONTROL

    Click here

  3. REMOVE REAR WHEEL

    Click here

  4. DRAIN BRAKE FLUID

    Note

    If brake fluid leaks onto any painted surface, immediately wash it off.

  5. LOOSEN NO. 1 WIRE ADJUSTING NUT

    for LHD: Click here

    for RHD: Click here

  6. REMOVE PARKING BRAKE LEVER PROTECTOR

    Click here

  7. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. B006HN4

      Remove the nut and separate the No. 3 parking brake cable assembly from the rear trailing arm assembly.

    2. B006IJV

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    3. B006I4LC06
      *1 Rear Disc Brake Cylinder Assembly
      *a Clip

      Disengage the clip and separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

  8. DISCONNECT REAR FLEXIBLE HOSE


    1. B006INC

      Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.

  9. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY


    1. B006HSOC01
      *a Turn
      *b Hold

      Hold the 2 rear disc brake pad guide pins and remove the 2 bolts and rear disc brake cylinder assembly from the disc brake cylinder mounting.

  10. REMOVE REAR DISC BRAKE PAD KIT


    1. B006HRI

      Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.

  11. REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT


    1. Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.

  12. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE


    1. B006HME

      Remove the 2 rear disc brake pad support plates from the rear disc brake cylinder mounting.

      Note

      Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.

  13. REMOVE REAR DISC BRAKE PAD GUIDE PIN


    1. B006IRK

      Remove the 2 rear disc brake pad guide pins from the rear disc brake cylinder mounting.

    2. B006HHOC02
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from each rear disc brake pad guide pin.

      Note

      Do not damage the rear disc brake pad guide pins.

  14. REMOVE REAR DISC BRAKE BUSHING DUST BOOT


    1. B006JAP

      Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.

  15. REMOVE REAR DISC BRAKE CYLINDER MOUNTING


    1. B006IPC

      Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle carrier sub-assembly.

  16. REMOVE REAR DISC


    1. B006J42C01
      *a Matchmark

      Put matchmarks on the rear disc and the rear axle hub and bearing assembly.

    2. Remove the rear disc.