SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P03402A, P034031

DTC Code DTC Name
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal

DESCRIPTION

Refer to DTC P034011.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range No camshaft position sensor signal is received by the ECM while the engine is cranking (1 trip detection logic).

  • Open or short in camshaft position sensor circuit

  • Camshaft position sensor

  • Intake camshaft

  • ECM

 Comes on DTC stored SAE Code: P0340
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal The camshaft position sensor signal is not received but a normal crankshaft position sensor signal received with the engine running at 600 rpm or higher (1 trip detection logic).

  • Open or short in camshaft position sensor circuit

  • Camshaft position sensor

  • Intake camshaft

  • ECM

 Comes on DTC stored SAE Code: P0340

Reference: Inspection using an oscilloscope.

Click here

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG).

  7. Turn the GTS on.

  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here

  9. Start the engine.

  10. Idle the engine for 10 seconds or more [A].

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [B].

  12. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  14. Input the DTC: P03402A or P034031.

  15. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE or N/A, perform steps [A] and [B] again.

WIRING DIAGRAM

Refer to DTC P034011.

Click here

CAUTION / NOTICE / HINT

Note


  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

Tech Tips


  • If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR

    B006HILC06
    *a

    Front view of wire harness connector

    (to Camshaft Position Sensor)

    Tech Tips

    Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


    1. Disconnect the camshaft position sensor connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      C18-3 (VC) - Body ground Power switch on (IG) 4.5 to 5.5 V
      C18-1 (VVI+) - Body ground Power switch on (IG) 3.0 to 5.0 V

    4. Turn the power switch off and wait for at least 30 seconds.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C18-3 (VC) - C18-1 (VVI+) Power switch off 1.425 to 1.575 kΩ
      C18-2 (VVI-) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) Click here

    OK

  2. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

    B006HYTC01
    *a Clearance

    1. Check the camshaft position sensor installation condition.

      OK
      Camshaft position sensor is installed correctly.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY REINSTALL CAMSHAFT POSITION SENSOR Click here

    OK

  3. INSPECT INTAKE CAMSHAFT (TIMING ROTOR)


    1. Check the timing rotor of the intake camshaft.

      OK
      Camshaft timing rotor does not have any cracks or deformation.

      Tech Tips

      Perform "Inspection After Repair" after replacing the intake camshaft.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CAMSHAFT POSITION SENSOR Click here

    NG

    REPLACE INTAKE CAMSHAFT Click here

  4. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)


    1. Disconnect the camshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C18-1 (VVI+) - C31-82 (VV1+) Always Below 1 Ω
      C18-2 (VVI-) - C31-115 (VV1-) Always Below 1 Ω
      C18-3 (VC) - C31-116 (VCV1) Always Below 1 Ω
      C18-1 (VVI+) or C31-82 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
      C18-2 (VVI-) or C31-115 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
      C18-3 (VC) or C31-116 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR