SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P00B115

DTC Code DTC Name
P00B115 Radiator Coolant Temperature Sensor Circuit Short to Battery or Open

DESCRIPTION

Refer to DTC P00B111.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P00B115 Radiator Coolant Temperature Sensor Circuit Short to Battery or Open The No. 2 engine coolant temperature sensor output voltage is higher than 4.91 V for 3 seconds or more (1 trip detection logic).

  • Open or short in No. 2 engine coolant temperature sensor circuit

  • No. 2 engine coolant temperature sensor

  • ECM

 Comes on DTC stored SAE Code: P00B4

MONITOR DESCRIPTION

The No. 2 engine coolant temperature sensor is used to monitor the engine coolant temperature. The No. 2 engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the engine coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance decreases. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the No. 2 engine coolant temperature sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction of the No. 2 engine coolant temperature sensor circuit, illuminate the MIL and stores a DTC.

Example:

If the No. 2 engine coolant temperature sensor output voltage is higher than 4.91 V for 3 seconds or more, the ECM store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG).

  7. Turn the GTS on.

  8. Wait 3 seconds or more.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes.

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P00B115.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P00B111.

Click here

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR


    1. Inspect the No. 2 engine coolant temperature sensor.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE COOLANT TEMPERATURE SENSOR - ECM)


    1. Disconnect the No. 2 engine coolant temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C29-2 - C31-87 (THTW) Always Below 1 Ω
      C29-1 - C31-88 (ETHT) Always Below 1 Ω
      C29-2 or C31-87 (THTW) - Other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR